[DeTomaso] Ignition key Lock - tumbler housing
Jim Wallace
pantera_4220 at yahoo.com
Sun Jun 9 05:19:48 EDT 2019
Wayne,
I would like to see some pictures.
Jim
On Saturday, June 8, 2019, 10:23:19 PM EDT, Wayne Boian <wayneboian at windstream.net> wrote:
Mike, thanks for the reply.
My car had some different issues so I continued on with the disassembly of
the tumbler from the tumbler housing. The notes at Pantera Place are spot on
about the need to keep the key inserted when removing the tumbler from the
housing to keep the pin plates from falling out. It turns out that the
problem was a spring in one of the pin plates was in a bind or jammed up
(stuck) causing the pin plate to not move freely. I did find some
metal/plating chips that should have not been there. The pins and springs
were removed for cleaning and then given a ultrasonic bath. After reassembly
it appears to be working correctly.
During the rebuild I could see other signs of age and wear, but this will
get the car running for now. I would like to find a new tumbler and housing
so if anyone has information on that please let me know.
On a different note, is there a policy/restrictions on posting pictures.?
Thanks
Wayne
-----Original Message-----
From: Mike Drew
Sent: Saturday, June 08, 2019 2:55 AM
To: Wayne Boian
Cc: detomaso at server.detomasolist.com
Subject: Re: [DeTomaso] Ignition key Lock - tumbler housing
Wayne,
If you pull the lock tumbler out, then insert the key fully, then depress it
inwards, it will probably turn. If the tumbler is in the ‘in’ position when
you first insert the key, then it cannot be turned.
Make a tiny hook from a paper clip to pop the tumbler out, then lubricate it
with lock lubricant. Chances are that is all that is necessary.
Mike
Sent from my iPad
> On Jun 7, 2019, at 22:32, Wayne Boian <wayneboian at windstream.net> wrote:
>
> It was a pretty day so I decided to take the Pantera out to awarm the
> oila. As fate would have it, I put the key in the ignition and the key
> would not turn. Long story short, did all the research and crawled up
> under the dash.
>
> I have the ignition parts out of the car and the problem is in the
> ignition lock or tumbler housing. The mechanical part that key goes
> into is bad and not the electrical part of the switch. The center
> section of the lock ( where the key is inserted) is free to move in and
> out and has no spring pressure. The key will just not turn in the
> tumbler housing. I would like to find a replacement ignition Lock ( if
> that is the correct name) before trying to take the old one apart.
> Mike at The Pantera Place warns that disassembly of the tumbler body
> can be a little tricky.
>
> I could not fine anything on just the tumbler housing in Bill Taylors
> Gear Head database, so if you have some information please let me know.
>
> Thanks
> Wayne
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.) use
> the links above.
>
> Members who post to this list grant license to the list to forward any
> message posted here to all past, current, or future members of the list.
> They also grant the list owner permission to maintain an archive or
> approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
Wayne,
I would like to see some pictures.
Jim
On Saturday, June 8, 2019, 10:23:19 PM EDT, Wayne Boian
<wayneboian at windstream.net> wrote:
Mike, thanks for the reply.
My car had some different issues so I continued on with the disassembly
of
the tumbler from the tumbler housing. The notes at Pantera Place are
spot on
about the need to keep the key inserted when removing the tumbler from
the
housing to keep the pin plates from falling out. It turns out that the
problem was a spring in one of the pin plates was in a bind or jammed
up
(stuck) causing the pin plate to not move freely. I did find some
metal/plating chips that should have not been there. The pins and
springs
were removed for cleaning and then given a ultrasonic bath. After
reassembly
it appears to be working correctly.
During the rebuild I could see other signs of age and wear, but this
will
get the car running for now. I would like to find a new tumbler and
housing
so if anyone has information on that please let me know.
On a different note, is there a policy/restrictions on posting
pictures.?
Thanks
Wayne
-----Original Message-----
From: Mike Drew
Sent: Saturday, June 08, 2019 2:55 AM
To: Wayne Boian
Cc: [1]detomaso at server.detomasolist.com
Subject: Re: [DeTomaso] Ignition key Lock - tumbler housing
Wayne,
If you pull the lock tumbler out, then insert the key fully, then
depress it
inwards, it will probably turn. If the tumbler is in the aina position
when
you first insert the key, then it cannot be turned.
Make a tiny hook from a paper clip to pop the tumbler out, then
lubricate it
with lock lubricant. Chances are that is all that is necessary.
Mike
Sent from my iPad
> On Jun 7, 2019, at 22:32, Wayne Boian <[2]wayneboian at windstream.net>
wrote:
>
> It was a pretty day so I decided to take the Pantera out to awarm
the
> oila. As fate would have it, I put the key in the ignition and the
key
> would not turn. Long story short, did all the research and crawled
up
> under the dash.
>
> I have the ignition parts out of the car and the problem is in the
> ignition lock or tumbler housing. The mechanical part that key goes
> into is bad and not the electrical part of the switch. The center
> section of the lock ( where the key is inserted) is free to move in
and
> out and has no spring pressure. The key will just not turn in the
> tumbler housing. I would like to find a replacement ignition Lock (
if
> that is the correct name) before trying to take the old one apart.
> Mike at The Pantera Place warns that disassembly of the tumbler
body
> can be a little tricky.
>
> I could not fine anything on just the tumbler housing in Bill
Taylors
> Gear Head database, so if you have some information please let me
know.
>
> Thanks
> Wayne
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> [3]DeTomaso at server.detomasolist.com
> [4]http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.)
use
> the links above.
>
> Members who post to this list grant license to the list to forward
any
> message posted here to all past, current, or future members of the
list.
> They also grant the list owner permission to maintain an archive or
> approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[5]DeTomaso at server.detomasolist.com
[6]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:detomaso at server.detomasolist.com
2. mailto:wayneboian at windstream.net
3. mailto:DeTomaso at server.detomasolist.com
4. http://server.detomasolist.com/mailman/listinfo/detomaso
5. mailto:DeTomaso at server.detomasolist.com
6. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list