[DeTomaso] Caliper rebuild kits...
Asa Jay Laughton
asajay at asajay.com
Fri May 18 13:53:05 EDT 2018
Those of you familiar with my Pantera (5533) which is now Steve's, will remember I rebuilt those calipers (all of them) for the 2012 SSCC. There should be no difficulty in getting them apart. Recall I created videos of the rebuilds as well.
The brakes have been driven hard during racing and are probably due to be rebuilt again. I only ran ATE 200 (amber) or Super Blue brake fluid and changed it every year I raced. I don't imagine they will be anywhere near the difficulty I had in getting them apart.
If Steve can find o-rings, it's probably all he'll need.
Steve,
The rear caliper piston must be clocked at 45 degrees for proper assembly and then clocked back to vertical for use. Don't force it or it will break. Didn't I give you a set of spare front calipers? I'd recommend getting full rebuild kits or see if you could do exchanges with Larry so you have a spare set at least for the fronts.
I'll see if I can find the videos.
Asa
Asa Jay Laughton, W7TSC, MSgt, USAFR, retired
Sent using Jedi Mind Tricks
On May 18, 2018, 10:10, at 10:10, Larry Stock <larrys at panteraparts.com> wrote:
>Of course you all know that these are square o-rings, and I¹m sure all
>4
>pistons will all easily come out together, NOT :~<(' so good luck with
>that.
>
>On 5/18/18, 9:58 AM, "DeTomaso on behalf of Julian Kift"
><detomaso-bounces at server.detomasolist.com on behalf of
>julian_kift at hotmail.com> wrote:
>
>> It appears there are a few o-ring / seal wholesale suppliers in
>> Portland/Beaverton, I'd pull an o-ring and go see if they can match
>it.
>>
>> Julian
>>
>__________________________________________________________________
>>
>> From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf
>of
>> Steve Lisa <stevelisa at patentit.com>
>> Sent: Friday, May 18, 2018 9:51 AM
>> To: Mike Drew
>> Cc: List DeTomaso Forum
>> Subject: Re: [DeTomaso] Caliper rebuild kits...
>>
>> Thanks....unfortunately we are just testing today. So I need it
>today.
>> I
>> will overnight some for tomorrow as well (Larry Stock) already
>found
>> me....
>> But the specs I have say 42.85 mm and 33.96 mm pistons. I (Google)
>> have
>> found other modern vehicles with the same size pistons. What are
>the
>> chances I can piece some o-rings together???
>> Regards,
>> Steven G. Lisa, Esq.
>> Email: SteveLisa at PatentIt.com
>> Direct: 312-320-5888
>> Scottsdale Office | P: 480.535.6656 | F: 480.535.6628 | A: 7689
>> East
>> Paradise Lane, Suite 2, Scottsdale, AZ 85260
>> Chicago Office | P: 312.752.4357 | F:312.896.5633 | A: 55 E.
>Monroe
>> Street, Suite 3800, Chicago, IL 60603
>> [1]www.PatentIt.com
>> This email is intended only for the recipient above, and may
>contain
>> confidential and privileged information. If you received this email
>in
>> error, please destroy it and indicate such by return email to me.
>Thank
>> you.,
>> On May 18, 2018 09:38, "Mike Drew" <MikeLDrew at aol.com> wrote:
>> Steven,
>> Sadly, absolutely not. The Pantera front brake calipers were only
>used
>> on
>> the Pantera, and the Fiat Dino coupe/Spyder. You won't find those
>at
>> Pep
>> Boys.
>> Pantera vendors carry them naturally, and can overnight a set to
>you so
>> you
>> don't have to be on the trailer...in fact many sell reman calipers
>> which
>> would be faster to install, and then you could rebuild yours in a
>> leisurely
>> manner and have them as spares....
>> Mike
>> Sent from my iPad
>> > On May 18, 2018, at 09:32, Steve Lisa <stevelisa at patentit.com>
>wrote:
>> >
>> > All, we are at PIR testing and sn5533 front calipers are
>leaking at
>> the
>> > piston seals.A We have no spare o-rings or rebuild. Are there
>any
>> > common/close size o-rings that we can get an the auto part
>store
>> that
>> > will work in the '73 front calipers?
>> > Regards,A
>> > Steven G. Lisa, Esq.A
>> > Email: SteveLisa at PatentIt.comA
>> > Direct:A 312-320-5888
>> > Scottsdale OfficeA |A P:A 480.535.6656A |A A F:A 480.535.6628A
>> > |A A A:A 7689 East Paradise Lane, Suite 2, Scottsdale, AZ 85260
>> > Chicago OfficeA |A P:A 312.752.4357A |A A F:312.896.5633A |A
>A
>> A:A 55
>> > E. Monroe Street, Suite 3800, Chicago, IL 60603
>> > [1]www.PatentIt.com
>> > This email is intended only for the recipient above, and may
>> contain
>> > confidential and privileged information. If you received this
>email
>> in
>> > error, please destroy it and indicate such by return email to
>me.
>> Thank
>> > you.
>> >
>> > References
>> >
>> > 1. [2]http://www.PatentIt.com/
>> > _______________________________________________
>> >
>> >
>> > Detomaso Email List is not managed by POCA
>> > Posted emails must not exceed 1.5 Megabytes
>> > DeTomaso mailing list
>> > DeTomaso at server.detomasolist.com
>> > [3]http://server.detomasolist.com/mailman/listinfo/detomaso
>> >
>> > To manage your subscription (change email address, unsubscribe,
>etc.)
>> use
>> the links above.
>> >
>> > Members who post to this list grant license to the list to
>forward
>> any
>> message posted here to all past, current, or future members of the
>> list.
>> They also grant the list owner permission to maintain an archive or
>> approve
>> the archiving of list messages.
>>
>>References
>>
>> 1. http://www.PatentIt.com/
>> 2. http://www.PatentIt.com/
>> 3. http://server.detomasolist.com/mailman/listinfo/detomaso
>>_______________________________________________
>>
>>
>>Detomaso Email List is not managed by POCA
>>Posted emails must not exceed 1.5 Megabytes
>>DeTomaso mailing list
>>DeTomaso at server.detomasolist.com
>>http://server.detomasolist.com/mailman/listinfo/detomaso
>>
>>To manage your subscription (change email address, unsubscribe, etc.)
>use
>>the links above.
>>
>>Members who post to this list grant license to the list to forward any
>>message posted here to all past, current, or future members of the
>list.
>>They also grant the list owner permission to maintain an archive or
>>approve the archiving of list messages.
>
>
>_______________________________________________
>
>
>Detomaso Email List is not managed by POCA
>Posted emails must not exceed 1.5 Megabytes
>DeTomaso mailing list
>DeTomaso at server.detomasolist.com
>http://server.detomasolist.com/mailman/listinfo/detomaso
>
>To manage your subscription (change email address, unsubscribe, etc.)
>use the links above.
>
>Members who post to this list grant license to the list to forward any
>message posted here to all past, current, or future members of the
>list. They also grant the list owner permission to maintain an archive
>or approve the archiving of list messages.
-------------- next part --------------
Those of you familiar with my Pantera (5533) which is now Steve's, will
remember I rebuilt those calipers (all of them) for the 2012 SSCC.A
There should be no difficulty in getting them apart.A Recall I created
videos of the rebuilds as well.
The brakes have been driven hard during racing and are probably due to
be rebuilt again.A I only ran ATE 200 (amber) or Super Blue brake
fluid and changed it every year I raced.A I don't imagine they will be
anywhere near the difficulty I had in getting them apart.
If Steve can find o-rings, it's probably all he'll need.
Steve,
The rear caliper piston must be clocked at 45 degrees for proper
assembly and then clocked back to vertical for use.A Don't force it or
it will break.A Didn't I give you a set of spare front calipers?A I'd
recommend getting full rebuild kits or see if you could do exchanges
with Larry so you have a spare set at least for the fronts.
I'll see if I can find the videos.
Asa
AsaA JayA Laughton, W7TSC, MSgt, USAFR, retired
Sent using Jedi Mind Tricks
On May 18, 2018, at 10:10, Larry Stock <[1]larrys at panteraparts.com>
wrote:
Of course you all know that these are square o-rings, and IA^1m sure all 4
pistons will all easily come out together, ANOT :~<(' so good luck with
that.
On 5/18/18, 9:58 AM, "DeTomaso on behalf of Julian Kift"
<detomaso-bounces at server.detomasolist.com on behalf of
julian_kift at hotmail.com> wrote:
It appears there are a few o-ring / seal wholesale suppliers in
Portland/Beaverton, I'd pull an o-ring and go see if they can match
it.
Julian
_______________________________________________________________
From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf
of
Steve Lisa <stevelisa at patentit.com>
Sent: Friday, May 18, 2018 9:51 AM
To: Mike Drew
Cc: List DeTomaso Forum
Subject: Re: [DeTomaso] Caliper rebuild kits...
Thanks....unfortunately we are just testing today. So I need it
today.
I
will overnight some for tomorrow as well (Larry Stock) already found
me....
But the specs I have say 42.85 mm and 33.96 mm pistons. I (Google)
have
found other modern vehicles with the same size pistons. What are the
chances I can piece some o-rings together???
Regards,
Steven G. Lisa, Esq.
Email: SteveLisa at PatentIt.com
Direct: 312-320-5888
Scottsdale Office | P: 480.535.6656 | F: 480.535.6628 | A: 7689
East
Paradise Lane, Suite 2, Scottsdale, AZ 85260
Chicago Office | P: 312.752.4357 | F:312.896.5633 | A: 55 E. Monroe
Street, Suite 3800, Chicago, IL 60603
[1][2]www.PatentIt.com
This email is intended only for the recipient above, and may contain
confidential and privileged information. If you received this email
in
error, please destroy it and indicate such by return email to me.
Thank
you.,
On May 18, 2018 09:38, "Mike Drew" <MikeLDrew at aol.com> wrote:
Steven,
Sadly, absolutely not. The Pantera front brake calipers were only
used
on
the Pantera, and the Fiat Dino coupe/Spyder. You won't find those at
Pep
Boys.
Pantera vendors carry them naturally, and can overnight a set to you
so
you
don't have to be on the trailer...in fact many sell reman calipers
which
would be faster to install, and then you could rebuild yours in a
leisurely
manner and have them as spares....
Mike
Sent from my iPad
On May 18, 2018, at 09:32, Steve Lisa <stevelisa at patentit.com>
wrote:
All, we are at PIR testing and sn5533 front calipers are leaking at
the
piston seals.A We have no spare o-rings or rebuild. Are there any
common/close size o-rings that we can get an the auto part store
that
will work in the '73 front calipers?
Regards,A
Steven G. Lisa, Esq.A
Email: SteveLisa at PatentIt.comA
Direct:A 312-320-5888
Scottsdale OfficeA |A P:A 480.535.6656A |A A F:A 480.535.6628A
|A A A:A 7689 East Paradise Lane, Suite 2, Scottsdale, AZ 85260
Chicago OfficeA |A P:A 312.752.4357A |A A F:312.896.5633A |A A
A:A 55
E. Monroe Street, Suite 3800, Chicago, IL 60603
[1][3]www.PatentIt.com
This email is intended only for the recipient above, and may
contain
confidential and privileged information. If you received this email
in
error, please destroy it and indicate such by return email to me.
Thank
you.
References
1. [2][4]http://www.PatentIt.com/
_______________________________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
[3][5]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe,
etc.)
use
the links above.
Members who post to this list grant license to the list to forward
any
message posted here to all past, current, or future members of the
list.
They also grant the list owner permission to maintain an archive or
approve
the archiving of list messages.
References
1. [6]http://www.PatentIt.com/
2. [7]http://www.PatentIt.com/
3. [8]http://server.detomasolist.com/mailman/listinfo/detomaso
_______________________________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
[9]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe,
etc.) use
the links above.
Members who post to this list grant license to the list to forward
any
message posted here to all past, current, or future members of the
list.
They also grant the list owner permission to maintain an archive or
approve the archiving of list messages.
_______________________________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
[10]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe,
etc.) use the links above.
Members who post to this list grant license to the list to forward
any message posted here to all past, current, or future members of
the list. They also grant the list owner permission to maintain an
archive or approve the archiving of list messages.
References
1. mailto:larrys at panteraparts.com
2. http://www.PatentIt.com/
3. http://www.PatentIt.com/
4. http://www.PatentIt.com/
5. http://server.detomasolist.com/mailman/listinfo/detomaso
6. http://www.PatentIt.com/
7. http://www.PatentIt.com/
8. http://server.detomasolist.com/mailman/listinfo/detomaso
9. http://server.detomasolist.com/mailman/listinfo/detomaso
10. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list