[DeTomaso] Clutch Pressure plate rebuilding
Mad Dog Antenucci
teampantera at yahoo.com
Thu Jun 19 21:51:59 EDT 2008
Hey Dick,
Thanks to all who responded on this subject.....And Dick, don't feel like the Lone Ranger.
Against Dick Drenske's advise I didn't replace or rebuild the pressure plate when I replaced the clutch and resurfaced the fly wheel. Yea, I know I should have. Planning to talk to the shop SOBill recommended next week...headed out the door to the airport right now...its only money! ;-]>
Dawg
Dick Koch <arkoch at earthlink.net> wrote: Chuck, I ran the RAM clutch and pressure plate they recommended for my
engine configuration and power output.. When I tore it up (my fault for
not installing it correctly) ), they rebuilt the pressure plate and
clutch for half of what a new set cost and it came back as "new" and
performed great. Worked fine until I didn't watch the free play on the
slave cylinder and spun it out.
I have never used a clutch rebuild shop and am not able to comment on
the quality of their work. However, I do know that by using RAM, if I
have a problem they will repair it to "as new" at about half the price
(did not include shipping). I assume the other major manufacturers
would do the same.
With all that said and done, it certainly is easier to just go buy a new
one.
Dick Koch - Atlanta
cengles at cox.net wrote:
> Dear Guys,
>
> Thanks for the short course on clutch and pressure plate rebuilding. I think I will stick with the old method of paying up for a new clutch and pressure plate the next time the problem comes up.
>
> Warmest regards, Chuck Engles
>
>
>
>
> ---- JDeRyke at aol.com wrote:
>
>> In a message dated 6/19/08 7:56:19 AM, cengles at cox.net writes:
>>
>>
>>> Can someone explain rebuilding pressure plates and clutches to me?
>>>
>>>
>> I've only seen it done once eons ago, at Bay City Friction in San Jose.
>> Pressure plates are rivited together and the rebuilder cuts the rivits and replaces
>> all the worn parts. The holding power of a pressure plate is in its springs-
>> whether its a stack of coil springs or a belleville spring as used in a
>> diaphragm pressure plate. The inherent value of a rebuilder is in the choice of
>> parts and the possibility of custom work available. A stock Pantera pressure plate
>> has around 1800 lbs force and 'racing' units are 2600 lbs and up, I think.
>> Custom covers are available that deflect less with heavy springs. Lightweight
>> aluminum covers and steel-sprayed aluminum pressure plate surfaces are used in
>> certain racing classes, but you won't find these at Pep Boyz! Plus, in a
>> Pantera, the Long type lever arms cannot have bob-weights on them as moving levers
>> will hit the inside of our bellhousing when the engine's running. There are 4
>> different Long clutch levers and only one type will fit, so Pantera
>> clutch-lever arms must be re-used or new ones modified to fit. Its also possible to have
>> a hybrid pressure plate built up using stock Long clutch parts with Borg &
>> Beck arms (used in Chryslers) that have roller bearings in their pivots for less
>> pedal effort and more even cover force with the same holding power. Lots of
>> possibilities and likely some new ones I never heard of, but not cheap. HP books
>> used to publish Tom Monroe's 'Clutch and Flywheel Handbook' thats good
>> reading, too. FWIW- J DeRyke
>>
>>
>> **************
>> Gas prices getting you down? Search AOL
>> Autos for fuel-efficient used cars.
>>
>> (http://autos.aol.com/used?ncid=aolaut00050000000007)
>>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
>
>
_______________________________________________
Detomaso Forum Managed by POCA
Archive Search Engine Now Available at http://www.realbig.com/detomaso/
DeTomaso mailing list
DeTomaso at list.realbig.com
http://list.realbig.com/mailman/listinfo/detomaso
Mad Dawg Antenucci
Team Pantera Racing
The 1st & still the only vintage race team in open road racing
www.teampanteraracing.com
More information about the DeTomaso
mailing list