[DeTomaso] door striker latch screw size?
Ken Green
kenn_green at yahoo.com
Sun Jan 9 15:21:51 EST 2022
Thanks, that sounds right.
Do you recall the correct bevel? 90 or 100 deg?
On Sunday, January 9, 2022, 09:05:05 AM PST, Doug Braun <doug351c at gmail.com> wrote:
Ken,
Yes, they are special. They have a non-standard (reduced) head diameter.
I remember buying Stainless Steel ones with the correct head bevel angle and then turning the heads down to get them right size.
Then I polished the heads and they ended up looking better than the original screws.
Doug Braun
-----Original Message-----
From: DeTomaso On Behalf Of Ken Green via DeTomaso
Sent: Saturday, January 8, 2022 9:41 PM
To: Detomaso List <detomaso at server.detomasolist.com>
Subject: [DeTomaso] door striker latch screw size?
Are these just a flat head screw. Look to be M8, McMaster has them with 90 and 100 deg tapers, but the heads on both are 16mm diameter and I think this it too large to fit into the recess in the latch?
Are these special "Italian" screw sizes?
Thanks
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
Thanks, that sounds right.
Do you recall the correct bevel? 90 or 100 deg?
On Sunday, January 9, 2022, 09:05:05 AM PST, Doug Braun
<doug351c at gmail.com> wrote:
Ken,
Yes, they are special. They have a non-standard (reduced) head
diameter.
I remember buying Stainless Steel ones with the correct head bevel
angle and then turning the heads down to get them right size.
Then I polished the heads and they ended up looking better than the
original screws.
Doug Braun
-----Original Message-----
From: DeTomaso On Behalf Of Ken Green via DeTomaso
Sent: Saturday, January 8, 2022 9:41 PM
To: Detomaso List <[1]detomaso at server.detomasolist.com>
Subject: [DeTomaso] door striker latch screw size?
Are these just a flat head screw. Look to be M8, McMaster has them
with 90 and 100 deg tapers, but the heads on both are 16mm diameter and
I think this it too large to fit into the recess in the latch?
Are these special "Italian" screw sizes?
Thanks
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[2]DeTomaso at server.detomasolist.com
[3]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:detomaso at server.detomasolist.com
2. mailto:DeTomaso at server.detomasolist.com
3. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list