[DeTomaso] Engine cover
Thomas Törnblom
thomas at hax.se
Mon Apr 27 00:02:37 EDT 2020
I used this style nuts when I had the engine out many years ago.
https://www.ebay.co.uk/itm/M4-M5-M6-M8-M10-Carbon-Steel-Tee-Spot-Slab-Based-T-Shape-Weld-Nuts-Flat-Holes/222910188029?hash=item33e67b89fd:m:mX3-8KT0vdHV5sUk854i14w
Thomas
> 27 apr. 2020 kl. 04:47 skrev Chuck and Linda Huber <lindahuber at cox.net>:
>
> From my point of view, it doen's matter what screws you use.
>
> Do what Larry (I think) did, get a piece of bar stock, and make 8-10 ALL NEW
> nuts, to fit your favorite screws (of a standard configuration). Cut them
> to size, and then install inside the captive housing on the firewall.
>
> Put a gob of RTV or silicone in with the nut, and then when they are all
> installed, put the bulkhead cover on with your new screws. The silicone
> will stiffen up with the nut in the right position, but will give the nut
> just a little play to make the threading / screw installation easier.
>
> Next pass - put a gasket between the engine cover.
>
> You can also use those black faucet washers (they are about 1/4" thick) as
> gaskets on the outslde of the screw - between the head and engine cover to
> provide a little bit of "give", and consistent compression.
>
> Regards -
>
> Chuck
>
> PS> If your car is 101% concourse, then you can ignore these suggestions.
>
>
>
>
> -----Original Message-----
> From: Mike Drew [mailto:MikeLDrew at aol.com]
> Sent: Sunday, April 26, 2020 3:58 PM
> To: Larry Finch
> Cc: Email List Address For Posting
> Subject: Re: [DeTomaso] Engine cover
>
> Larry,
>
> I found one in my parts stash:
>
>
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>
> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
>
> !DSPAM:5ea647cf18529301665669!
>
-------------- next part --------------
I used this style nuts when I had the engine out many years ago.
[1]https://www.ebay.co.uk/itm/M4-M5-M6-M8-M10-Carbon-Steel-Tee-Spot-Sla
b-Based-T-Shape-Weld-Nuts-Flat-Holes/222910188029?hash=item33e67b89fd:m
:mX3-8KT0vdHV5sUk854i14w
Thomas
27 apr. 2020 kl. 04:47 skrev Chuck and Linda Huber
<lindahuber at cox.net>:
From my point of view, it doen's matter what screws you use.
Do what Larry (I think) did, get a piece of bar stock, and make 8-10
ALL NEW
nuts, to fit your favorite screws (of a standard configuration). Cut
them
to size, and then install inside the captive housing on the firewall.
Put a gob of RTV or silicone in with the nut, and then when they are
all
installed, put the bulkhead cover on with your new screws. The
silicone
will stiffen up with the nut in the right position, but will give the
nut
just a little play to make the threading / screw installation easier.
Next pass - put a gasket between the engine cover.
You can also use those black faucet washers (they are about 1/4" thick)
as
gaskets on the outslde of the screw - between the head and engine cover
to
provide a little bit of "give", and consistent compression.
Regards -
Chuck
PS> If your car is 101% concourse, then you can ignore these
suggestions.
-----Original Message-----
From: Mike Drew [mailto:MikeLDrew at aol.com]
Sent: Sunday, April 26, 2020 3:58 PM
To: Larry Finch
Cc: Email List Address For Posting
Subject: Re: [DeTomaso] Engine cover
Larry,
I found one in my parts stash:
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
!DSPAM:5ea647cf18529301665669!
References
1. https://www.ebay.co.uk/itm/M4-M5-M6-M8-M10-Carbon-Steel-Tee-Spot-Slab-Based-T-Shape-Weld-Nuts-Flat-Holes/222910188029?hash=item33e67b89fd:m:mX3-8KT0vdHV5sUk854i14w
More information about the DeTomaso
mailing list