[DeTomaso] NPC: speed (Pal) nuts
doug351c
doug351c at gmail.com
Sun Apr 6 01:25:53 EDT 2014
It's not a dumb question and no I hadn't though of contacting a music store
or Gibson since the amp is so old - but it's probably worth at try.
I also tried an 8-32 Pal nut I had with a #8 sheet metal screw (which has 14
threads/inch) and it works fine. So its a good bet that the 6-32 Pal nuts I
have coming from McMaster-Carr will fit the #6 sheet metal stud (20
threads/inch) in the Gibson amp.
Doug
-----Original Message-----
From: Curt Hall [mailto:cuvee at sbcglobal.net]
Sent: Saturday, April 05, 2014 5:05 PM
To: doug351c at gmail.com; POCA Forum Mailing List
Subject: Re: [DeTomaso] NPC: speed (Pal) nuts
Dumb question...have you tried any of the local Music stores? If your not
in a hurry contact Gibson, but I'm sure you've thought of that already?
From: doug351c <doug351c at gmail.com>
To: POCA Forum Mailing List <detomaso at poca.com>
Sent: Saturday, April 5, 2014 2:15 PM
Subject: [DeTomaso] NPC: speed (Pal) nuts
Anyone run across a supplier for this type of speed nut (see attached
pic).
I need it to fit a #6 sheet metal screw with the most common type "AB"
thread/point which I believe is 20 threads per inch.
I've also seen these called "Pal" nuts but the Pal type may only apply to
a
machine thread which in this case would be 6-32.
Which brings up another question - anyone seen a size chart for sheet
metal
screw thread pitches?
BTW: I need this to restore a vintage Gibson guitar amp for my son Steve.
Doug Braun
blue 73L #5505
_______________________________________________
Detomaso Forum Managed by POCA
DeTomaso mailing list
DeTomaso at poca.com
http://poca.com/mailman/listinfo/detomaso_poca.com
-------------- next part --------------
It's not a dumb question and no I hadn't though of contacting a music
store or Gibson since the amp is so old - but it's probably worth at
try.
I also tried an 8-32 Pal nut I had with a #8 sheet metal screw (which
has 14 threads/inch) and it works fine. So its a good bet that the
6-32 Pal nuts I have coming from McMaster-Carr will fit the #6 sheet
metal stud (20 threads/inch) in the Gibson amp.
Doug
-----Original Message-----
From: Curt Hall [mailto:cuvee at sbcglobal.net]
Sent: Saturday, April 05, 2014 5:05 PM
To: doug351c at gmail.com; POCA Forum Mailing List
Subject: Re: [DeTomaso] NPC: speed (Pal) nuts
Dumb question...have you tried any of the local Music stores? If your
not in a hurry contact Gibson, but I'm sure you've thought of that
already?
From: doug351c <doug351c at gmail.com>
To: POCA Forum Mailing List <detomaso at poca.com>
Sent: Saturday, April 5, 2014 2:15 PM
Subject: [DeTomaso] NPC: speed (Pal) nuts
Anyone run across a supplier for this type of speed nut (see attached
pic).
I need it to fit a #6 sheet metal screw with the most common type "AB"
thread/point which I believe is 20 threads per inch.
I've also seen these called "Pal" nuts but the Pal type may only apply
to a
machine thread which in this case would be 6-32.
Which brings up another question - anyone seen a size chart for sheet
metal
screw thread pitches?
BTW: I need this to restore a vintage Gibson guitar amp for my son
Steve.
Doug Braun
blue 73L #5505
_______________________________________________
Detomaso Forum Managed by POCA
DeTomaso mailing list
[1]DeTomaso at poca.com
[2]http://poca.com/mailman/listinfo/detomaso_poca.com
References
1. mailto:DeTomaso at poca.com
2. http://poca.com/mailman/listinfo/detomaso_poca.com
More information about the DeTomaso
mailing list