[DeTomaso] Removing ANSA resonator tips?
jtaphorn at kingwoodcable.com
jtaphorn at kingwoodcable.com
Thu Aug 16 18:44:21 EDT 2012
allright, you guys have me motivated. 8 -10 extra HP is nothing to sneeze at. I'll build a tool for the job. My thought is to take a hole saw that fits snug in the muffler tip. The half way down the length of the hole saw, cut it around it's circumference. I'll then weld in a 12" section of pipe with a similar OD to extend its reach. A pilot using a wooden dowel ought to be sufficient to guide for the first cut and I will remove the dowel and let the outer resonator pipe be my guide for the back cut.
Perhaps this weekend. I'll let you know my results.
JT
---- Julian Kift <julian_kift at hotmail.com> wrote:
=============
If Andy still has stock Ansa mufflers then drilling the plate at the bottom of the tips/end of the muffler box is more important initially than removing the resonators IMO, I did mine with an extra long HSS drill bit and drilled a bunch of holes. Not easy to get the drill started as it is at an angle on the surface you are drilling.
I still need to get around to doing the full gutting at some point.
Julian
> From: dave at damardirect.com
> To: guson at home.se; MikeLDrew at aol.com
> Date: Thu, 16 Aug 2012 10:10:24 -0400
> CC: detomaso at realbig.com
> Subject: Re: [DeTomaso] Removing ANSA resonator tips?
>
> I have successfully used a bit extension (10-12") for drilling through walls. I would think it would work for a hole saw.
>
> IndyDave
>
> -----Original Message-----
> From: Tomas Gunnarsson [mailto:guson at home.se]
> Sent: Wednesday, August 15, 2012 8:51 AM
> To: MikeLDrew at aol.com
> Cc: detomaso at realbig.com
> Subject: Re: [DeTomaso] Removing ANSA resonator tips?
>
> A Dremel like tool should do the same job as a hole saw close to the tip but if the insert is welded at the oposite end neither a normal hole saw nor a grinding tool will reach that deep.
>
> Tomas
>
> <-----Ursprungligt Meddelande----->
> From: MikeLDrew at aol.com [MikeLDrew at aol.com]
> Sent: 15/8/2012 2:18:27 PM
> To: detomaso at realbig.com
> Subject: [DeTomaso] Removing ANSA resonator tips?
>
> Hi guys,
>
> Has anybody successfully removed ANSA resonators from the tips, leaving just the chrome tips? The resonators provide quite a restriction to exhaust flow, and Andy in the UK (he of the launching GT5-S) is looking for cheap horsepower. I seem to remember somebody successfully doing the job with a holesaw with the mufflers still on the car?
>
> Mike
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
> .
>
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
_______________________________________________
Detomaso Forum Managed by POCA
Archive Search Engine Now Available at http://www.realbig.com/detomaso/
DeTomaso mailing list
DeTomaso at list.realbig.com
http://list.realbig.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list