[DeTomaso] Angående: Re: pushrod length

[Thomas Törnblom]

I just measured the length of my two adjustable pushrods. One was around 200 mm and the other 205.
Those were used when I installed my first hydraulic roller.
I’d say the 7.5” to 8.7” will probably be the right one.

/Thomas

> 17 feb. 2021 kl. 08:59 skrev Charles McCall <charlesmccall at gmail.com>:
> 
>    What range adjustable pushrod do I need? On Summit I see:
>   7.5 to 8.7 inch
>   6.125 to 7.5 inch
>   7.8 to 8.8 inch.... any recommendations?A
> 
>   On Wed, Feb 17, 2021 at 1:00 PM gudmund frA,land
>   <[1]gudmundfroiland at yahoo.no> wrote:
> 
>     Hi Charles.A  I would recomend you to by one adjustable pushrod and
>     physical meshure the lengst you nead after the engine is asembled. I
>     think that is the onley way to get the propper lengte?A
> 
>   [2]Sendt fra Yahoo Mail pAYEN Android
> 
>   Den ons. 17. feb.. 2021 kl. 6.55 skrev Charles McCall
>   <[3]charlesmccall at gmail.com>:
> 
>   A  Good point Julian. The last stroker they put in a Pantera was 4-5
>   years
>   A  ago now and is in Oriol's car (don't know if you met him - I don't
>   A  remember who attended which years of LMC sometimes). They also did
>   A  another Cleveland about the same time for another Pantera, and
>   Oriol's
>   A  GT40 is running well and gets regular use. But they are far from
>   A  experts in the Cleveland.A
>   A  At some point you take a decision - you either go ahead selecting a
>   A  shop based on some references or you don't... the oil leak has been
>   10
>   A  years now so I wanted to fix it while the car is sitting. But the
>   shop
>   A  definitely needs a helping hand and I have my fingers crossed....
>   A  On Wed, Feb 17, 2021 at 8:56 AM Julian Kift
>   A  <[1][4]julian_kift at hotmail.com> wrote:
>   A  They may have assembled American V8's, the crucial question to ask
>   here
>   A  is how long did they stay together.... I suggest they acquire or
>   A  fabricate a tool, not too hard with some small threaded rod, steel
>   tube
>   A  and a thread tap. I'm across town from Summit Racing Sparks NV
>   store,
>   A  if you need something purchased and shipped out to them for peace of
>   A  mind let me know.
>   A  Julian
>   A  A
>   __________________________________________________________________
>   A  From: DeTomaso <[2][5]detomaso-bounces at server.detomasolist.com> on
>   behalf
>   A  of [3][6]charlesmccall at gmail.com <[4][7]charlesmccall at gmail.com>
>   A  Sent: Tuesday, February 16, 2021 7:12 PM
>   A  To: [5][8]detomaso at server.detomasolist.com
>   A  <[6][9]detomaso at server.detomasolist.com>
>   A  Subject: [DeTomaso] pushrod length
>   A  A
>   A  Hi all
>   A  My motor is apart to fix an oil leak by changing the cam, installing
>   a
>   A  stroker crank, new pistons, con-rods etc. I sure hope this fixes the
>   A  oil
>   A  leak! The shop doing the work doesn't have a gauge-thing to measure
>   the
>   A  desired pushrod length, and I shouldn't re-use the old ones as I now
>   A  have
>   A  hydraulic roller lifters instead of solid lifters, a different cam,
>   A  etc. Is
>   A  there any way to calculate correct pushrod length without this
>   little
>   A  tool?
>   A  Any suggestions? The shop is located in Spain and has assembled
>   other
>   A  American V-8s if all the parts are provided.
>   A  A
>   A  Thank you!
>   A  Classification: Restricted
>   References
>   A  1. mailto:[10]julian_kift at hotmail.com
>   A  2. mailto:[11]detomaso-bounces at server.detomasolist.com
>   A  3. mailto:[12]charlesmccall at gmail.com
>   A  4. mailto:[13]charlesmccall at gmail.com
>   A  5. mailto:[14]detomaso at server.detomasolist.com
>   A  6. mailto:[15]detomaso at server.detomasolist.com
> 
> References
> 
>   1. mailto:gudmundfroiland at yahoo.no
>   2. https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature
>   3. mailto:charlesmccall at gmail.com
>   4. mailto:julian_kift at hotmail.com
>   5. mailto:detomaso-bounces at server.detomasolist.com
>   6. mailto:charlesmccall at gmail.com
>   7. mailto:charlesmccall at gmail.com
>   8. mailto:detomaso at server.detomasolist.com
>   9. mailto:detomaso at server.detomasolist.com
>  10. mailto:julian_kift at hotmail.com
>  11. mailto:detomaso-bounces at server.detomasolist.com
>  12. mailto:charlesmccall at gmail.com
>  13. mailto:charlesmccall at gmail.com
>  14. mailto:detomaso at server.detomasolist.com
>  15. mailto:detomaso at server.detomasolist.com
> 
> 
> !DSPAM:602cccc61558510613464!
> _______________________________________________
> 
> 
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
> 
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
> 
> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
> 
> !DSPAM:602cccc61558510613464!