[DeTomaso] Engine Questions
Dave Londry
davel at trguys.com
Thu Apr 4 17:38:27 EDT 2019
Kevco is good stuff & still made in Minnesota as of 2 years go.
They've been $355 for quite a while.
If you don't use the bung on the front, take it out and use thread
sealant on it.
Dave
On 2019-04-04 10:33 a.m., Julian Kift wrote:
> You might consider a billet steel flywheel, which will be somewhere
> between the aluminum and stock for rotating mass.
>
> There are any number of aftermarket water pumps available with
> increased flow, some have the bypass some do not and I do not recall
> which currently, maybe you have that figured out only quoting
> Flowkooler and Edelbrock? Without the bypass the correct 351C
> thermostat with the hat and block off are redundant as no bypass can
> occur.
>
> Scott at SACC Restorations also sells a water pump overdrive pulley
> that will increase flow by a further 11%.
>
> I have heard good feedback on the Kevko oil pan, basically the same
> design and used to be about half the price of Aviaid or Armando, but in
> looking I see they are now $355 and you have to purchase the pickup
> separate for an additional $60.
>
> [1]https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
>
> FYI Aviaid/Armando Pantera pans no longer have an oil temperature bung
> standard, so if you want that capability be sure to call it out on
> ordering.
>
> Stock 351C timing pointers were almost unobtainium for a while with
> only used ones occasionally coming up on eBay and selling for inflated
> prices, but I thought someone tooled up and is making them again? I
> don't believe they are Pantera specific, the crank pulley however is.
> When you do get a pointer don't rely on it and the harmonic balancer
> lining up at the mark when the engine is at TDC, do a physical check
> and if necessary re-mark or adjust the pointer. Taking the time to mark
> up the flywheel is also a time saver allowing checking timing via the
> hole in the ZF bellhousing.
>
> Julian
> __________________________________________________________________
>
> From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf of
> Mike Drew via DeTomaso <detomaso at server.detomasolist.com>
> Sent: Thursday, April 4, 2019 9:43 AM
> To: Richard Greenblum
> Cc: detomaso
> Subject: Re: [DeTomaso] Engine Questions
>
> > On Apr 4, 2019, at 09:24, Richard Greenblum
> <richard at richardgreenblum.com> wrote:
> >
> > I'm at it with questions again...are 351C flywheels 164 tooth?
> >>>Yes.
> If you use a Fidanza flywheel they don't countersink the pressure plate
> mounting bolts properly. That takes a few minutes with a drill press to
> resolve.
> I have a Fidanza flywheel on my striker and it's great but there are
> definite trade offs. It lurches and bucks in traffic requiring clutch
> slipping. Simply not enough flywheel effect. If you are going to spend
> much time at low speeds or in traffic you might be happier with a stock
> flywheel. Plus you already have one so there is a cost savings there.
> >
> >
> > > I'd like to know your experience/opinions on:
> >
> >
> > Water Pumps--Flowkooler vs. Edelbrock
> >>>Both are fine. Flowkooler made in China, Edelbrock 100% US made in
> Torrance CA. I use Edelbrock.
> >
> > > Oil Pans--Aviaid vs. Armando (Mike explained they're basically the
> same
> > with Armando having come from Aviaid, but I thought there was some
> > concern with the pan rails on Aramandos at one time)
> >>>They are identical. Both have issues because they start off using
> cheap Chinese stock pans as cores, then cut them apart to customize
> them.
> >
> >
> > > Does anyone have a stock timing pointer they're willing to sell,
> or is
> > this a prayer at a junkyard item? Trying to avoid having to take
> it
> > off the engine in the car...
> >
> > >>>I believe, but am not sure, that the Pantera pointer is
> Pantera-specific? Others would know far more than I would about that.
> Mike
> >
> _______________________________________________
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> [2]http://server.detomasolist.com/mailman/listinfo/detomaso
> To manage your subscription (change email address, unsubscribe, etc.)
> use the links above.
> Members who post to this list grant license to the list to forward any
> message posted here to all past, current, or future members of the
> list. They also grant the list owner permission to maintain an archive
> or approve the archiving of list messages.
>
> References
>
> 1. https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
> 2. http://server.detomasolist.com/mailman/listinfo/detomaso
>
>
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>
> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
--
Dave Londry
TRGuys.com
davel at trguys.com
Cell 604-721-2278
Landline 604-589-9182
Skype embeddedspaces
-------------- next part --------------
Kevco is good stuff & still made in Minnesota as of 2 years go.
They've been $355 for quite a while.
If you don't use the bung on the front, take it out and use thread
sealant on it.
Dave
On 2019-04-04 10:33 a.m., Julian Kift wrote:
You might consider a billet steel flywheel, which will be somewhere
between the aluminum and stock for rotating mass.
There are any number of aftermarket water pumps available with
increased flow, some have the bypass some do not and I do not recall
which currently, maybe you have that figured out only quoting
Flowkooler and Edelbrock? Without the bypass the correct 351C
thermostat with the hat and block off are redundant as no bypass can
occur.
Scott at SACC Restorations also sells a water pump overdrive pulley
that will increase flow by a further 11%.
I have heard good feedback on the Kevko oil pan, basically the same
design and used to be about half the price of Aviaid or Armando, but in
looking I see they are now $355 and you have to purchase the pickup
separate for an additional $60.
[1][1]https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
FYI Aviaid/Armando Pantera pans no longer have an oil temperature bung
standard, so if you want that capability be sure to call it out on
ordering.
Stock 351C timing pointers were almost unobtainium for a while with
only used ones occasionally coming up on eBay and selling for inflated
prices, but I thought someone tooled up and is making them again? I
don't believe they are Pantera specific, the crank pulley however is.
When you do get a pointer don't rely on it and the harmonic balancer
lining up at the mark when the engine is at TDC, do a physical check
and if necessary re-mark or adjust the pointer. Taking the time to mark
up the flywheel is also a time saver allowing checking timing via the
hole in the ZF bellhousing.
Julian
__________________________________________________________________
From: DeTomaso [2]<detomaso-bounces at server.detomasolist.com> on behalf of
Mike Drew via DeTomaso [3]<detomaso at server.detomasolist.com>
Sent: Thursday, April 4, 2019 9:43 AM
To: Richard Greenblum
Cc: detomaso
Subject: Re: [DeTomaso] Engine Questions
> On Apr 4, 2019, at 09:24, Richard Greenblum
[4]<richard at richardgreenblum.com> wrote:
>
> I'm at it with questions again...are 351C flywheels 164 tooth?
>>>Yes.
If you use a Fidanza flywheel they don't countersink the pressure plate
mounting bolts properly. That takes a few minutes with a drill press to
resolve.
I have a Fidanza flywheel on my striker and it's great but there are
definite trade offs. It lurches and bucks in traffic requiring clutch
slipping. Simply not enough flywheel effect. If you are going to spend
much time at low speeds or in traffic you might be happier with a stock
flywheel. Plus you already have one so there is a cost savings there.
>
>
> > I'd like to know your experience/opinions on:
>
>
> Water Pumps--Flowkooler vs. Edelbrock
>>>Both are fine. Flowkooler made in China, Edelbrock 100% US made in
Torrance CA. I use Edelbrock.
>
> > Oil Pans--Aviaid vs. Armando (Mike explained they're basically the
same
> with Armando having come from Aviaid, but I thought there was some
> concern with the pan rails on Aramandos at one time)
>>>They are identical. Both have issues because they start off using
cheap Chinese stock pans as cores, then cut them apart to customize
them.
>
>
> > Does anyone have a stock timing pointer they're willing to sell,
or is
> this a prayer at a junkyard item? Trying to avoid having to take
it
> off the engine in the car...
>
> >>>I believe, but am not sure, that the Pantera pointer is
Pantera-specific? Others would know far more than I would about that.
Mike
>
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[5]DeTomaso at server.detomasolist.com
[2][6]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. [7]https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
2. [8]http://server.detomasolist.com/mailman/listinfo/detomaso
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[9]DeTomaso at server.detomasolist.com
[10]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the li
nks above.
Members who post to this list grant license to the list to forward any message p
osted here to all past, current, or future members of the list. They also grant
the list owner permission to maintain an archive or approve the archiving of lis
t messages.
--
Dave Londry
TRGuys.com
[11]davel at trguys.com
Cell 604-721-2278
Landline 604-589-9182
Skype embeddedspaces
References
1. https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
2. mailto:detomaso-bounces at server.detomasolist.com
3. mailto:detomaso at server.detomasolist.com
4. mailto:richard at richardgreenblum.com
5. mailto:DeTomaso at server.detomasolist.com
6. http://server.detomasolist.com/mailman/listinfo/detomaso
7. https://kevkoracing.com/products/part-f602-400-m-ford-pantera-pan
8. http://server.detomasolist.com/mailman/listinfo/detomaso
9. mailto:DeTomaso at server.detomasolist.com
10. http://server.detomasolist.com/mailman/listinfo/detomaso
11. mailto:davel at trguys.com
More information about the DeTomaso
mailing list