[DeTomaso] Spinning wheel stud

[Ken Green]

Can you use an inspection camera to look from the back and see if you can get to the back of the studs with the carrier assembled?  Otherwise you will still have to dissemble the carrier to replace the studs even if you can somehow get the nuts off.
Ken



      From: sean mundy <seanmundy at hotmail.com>
 To: "detomaso at server.detomasolist.com" <detomaso at server.detomasolist.com> 
 Sent: Sunday, July 15, 2018 12:41 PM
 Subject: [DeTomaso] Spinning wheel stud
   
  My weekend project was to remove my rear wheels and check my rear brake
  pad wear.  Oops, 2 of the pside lug nuts just spin and won't loosen
  up.  It looks like the studs are spinning and stripped.  First I have
  to figure out how to get the lug nuts off. Drilling?  I replaced the
  rear bearings over 10yrs ago so I know what a PITA removing the hub is
  going to be..  Assume I will need rear disk replacement so what are my
  affordable options?  I've spent a lot of time searching the forum for
  info but its a bit overwhelming.  Sean M
_______________________________________________


Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso

To manage your subscription (change email address, unsubscribe, etc.) use the links above.

Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.

   
-------------- next part --------------
   Can you use an inspection camera to look from the back and see if you
   can get to the back of the studs with the carrier assembled?  Otherwise
   you will still have to dissemble the carrier to replace the studs even
   if you can somehow get the nuts off.
   Ken
     __________________________________________________________________

   From: sean mundy <seanmundy at hotmail.com>
   To: "detomaso at server.detomasolist.com"
   <detomaso at server.detomasolist.com>
   Sent: Sunday, July 15, 2018 12:41 PM
   Subject: [DeTomaso] Spinning wheel stud
     My weekend project was to remove my rear wheels and check my rear
   brake
     pad wear.  Oops, 2 of the pside lug nuts just spin and won't loosen
     up.  It looks like the studs are spinning and stripped.  First I have
     to figure out how to get the lug nuts off. Drilling?  I replaced the
     rear bearings over 10yrs ago so I know what a PITA removing the hub
   is
     going to be..  Assume I will need rear disk replacement so what are
   my
     affordable options?  I've spent a lot of time searching the forum for
     info but its a bit overwhelming.  Sean M
   _______________________________________________
   Detomaso Email List is not managed by POCA
   Posted emails must not exceed 1.5 Megabytes
   DeTomaso mailing list
   [1]DeTomaso at server.detomasolist.com
   [2]http://server.detomasolist.com/mailman/listinfo/detomaso
   To manage your subscription (change email address, unsubscribe, etc.)
   use the links above.
   Members who post to this list grant license to the list to forward any
   message posted here to all past, current, or future members of the
   list. They also grant the list owner permission to maintain an archive
   or approve the archiving of list messages.

References

   1. mailto:DeTomaso at server.detomasolist.com
   2. http://server.detomasolist.com/mailman/listinfo/detomaso