[DeTomaso] Spinning wheel stud
B Hower
b.hower3400 at yahoo.com
Sun Jul 15 17:43:48 EDT 2018
Just a thought. Would it be possible to use a rotary disk to cut a slot in end of stud ( could also cut into nut ). Then use screw driver to hold stud while turning nut off of stud ....
Bud #3400 ( Drive it like there is no tomorrow -- for there may not be ! )
On Sunday, July 15, 2018, 4:28:13 PM CDT, Mike Drew via DeTomaso <detomaso at server.detomasolist.com> wrote:
Guys,
I don't think there is any 'hammer action' if the stud is spinning freely...?
Mike
Sent from my iPhone
> On Jul 15, 2018, at 14:14, Thomas Törnblom <thomas at hax.se> wrote:
>
> I think a pneumatic impact wrench would work better than an electric. More hammer action.
>
>> 15 juli 2018 kl. 22:37 skrev sean mundy <seanmundy at hotmail.com>:
>>
>> Yes. I'm using my electric impact gun. 3 lug nuts came off ok. 2
>> remain spinning. I've take my wheels off probably more than most
>> people. Maybe I just wore the wheel studs out with fatigue
>>
>> Sent from my iPhone
>>
>> On Jul 15, 2018, at 1:34 PM, Bjoern Flesland <[1]bflesland at gmail.com>
>> wrote:
>>
>> Hi Sean,
>> Did you try loosening your spinning lug nuts with a proper air gun?
>> Just a thought...
>> Cheers Bjoern
>> so/n. 15. jul. 2018 kl. 21.41 skrev sean mundy
>> <[2]seanmundy at hotmail.com>:
>>
>> My weekend project was to remove my rear wheels and check my rear
>> brake
>> pad wear. Oops, 2 of the pside lug nuts just spin and won't
>> loosen
>> up. It looks like the studs are spinning and stripped. First I
>> have
>> to figure out how to get the lug nuts off. Drilling? I replaced
>> the
>> rear bearings over 10yrs ago so I know what a PITA removing the
>> hub is
>> going to be.. Assume I will need rear disk replacement so what
>> are my
>> affordable options? I've spent a lot of time searching the forum
>> for
>> info but its a bit overwhelming. Sean M
>> _______________________________________________
>> Detomaso Email List is not managed by POCA
>> Posted emails must not exceed 1.5 Megabytes
>> DeTomaso mailing list
>> [3]DeTomaso at server.detomasolist.com
>> [4]http://server.detomasolist.com/mailman/listinfo/detomaso
>> To manage your subscription (change email address, unsubscribe,
>> etc.) use the links above.
>> Members who post to this list grant license to the list to forward
>> any message posted here to all past, current, or future members of
>> the list. They also grant the list owner permission to maintain an
>> archive or approve the archiving of list messages.
>>
>> References
>>
>> 1. mailto:bflesland at gmail.com
>> 2. mailto:seanmundy at hotmail.com
>> 3. mailto:DeTomaso at server.detomasolist.com
>> 4. http://server.detomasolist.com/mailman/listinfo/detomaso
>>
>>
>> !DSPAM:5b4bb0a6259881299117678!
>> _______________________________________________
>>
>>
>> Detomaso Email List is not managed by POCA
>> Posted emails must not exceed 1.5 Megabytes
>> DeTomaso mailing list
>> DeTomaso at server.detomasolist.com
>> http://server.detomasolist.com/mailman/listinfo/detomaso
>>
>> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>>
>> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
>>
>> !DSPAM:5b4bb0a6259881299117678!
>
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>
> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
Just a thought. Would it be possible to use a rotary disk to cut a slot
in end of stud ( could also cut into nut ). Then use screw driver to
hold stud while turning nut off of stud ....
Bud #3400 ( Drive it like there is no tomorrow -- for there may not be
! )
On Sunday, July 15, 2018, 4:28:13 PM CDT, Mike Drew via DeTomaso
<detomaso at server.detomasolist.com> wrote:
Guys,
I don't think there is any 'hammer action' if the stud is spinning
freely...?
Mike
Sent from my iPhone
> On Jul 15, 2018, at 14:14, Thomas TAP:rnblom <[1]thomas at hax.se>
wrote:
>
> I think a pneumatic impact wrench would work better than an electric.
More hammer action.
>
>> 15 juli 2018 kl. 22:37 skrev sean mundy <[2]seanmundy at hotmail.com>:
>>
>> Yes. I'm using my electric impact gun. 3 lug nuts came off ok. 2
>> remain spinning. I've take my wheels off probably more than most
>> people. Maybe I just wore the wheel studs out with fatigue
>>
>> Sent from my iPhone
>>
>> On Jul 15, 2018, at 1:34 PM, Bjoern Flesland
<[1][3]bflesland at gmail.com>
>> wrote:
>>
>> Hi Sean,
>> Did you try loosening your spinning lug nuts with a proper air gun?
>> Just a thought...
>> Cheers Bjoern
>> so/n. 15. jul. 2018 kl. 21.41 skrev sean mundy
>> <[2][4]seanmundy at hotmail.com>:
>>
>> My weekend project was to remove my rear wheels and check my
rear
>> brake
>> pad wear. Oops, 2 of the pside lug nuts just spin and won't
>> loosen
>> up. It looks like the studs are spinning and stripped. First
I
>> have
>> to figure out how to get the lug nuts off. Drilling? I
replaced
>> the
>> rear bearings over 10yrs ago so I know what a PITA removing the
>> hub is
>> going to be.. Assume I will need rear disk replacement so what
>> are my
>> affordable options? I've spent a lot of time searching the
forum
>> for
>> info but its a bit overwhelming. Sean M
>> _______________________________________________
>> Detomaso Email List is not managed by POCA
>> Posted emails must not exceed 1.5 Megabytes
>> DeTomaso mailing list
>> [3][5]DeTomaso at server.detomasolist.com
>> [4][6]http://server.detomasolist.com/mailman/listinfo/detomaso
>> To manage your subscription (change email address, unsubscribe,
>> etc.) use the links above.
>> Members who post to this list grant license to the list to
forward
>> any message posted here to all past, current, or future members
of
>> the list. They also grant the list owner permission to maintain
an
>> archive or approve the archiving of list messages.
>>
>> References
>>
>> 1. mailto:[7]bflesland at gmail.com
>> 2. mailto:[8]seanmundy at hotmail.com
>> 3. mailto:[9]DeTomaso at server.detomasolist.com
>> 4. [10]http://server.detomasolist.com/mailman/listinfo/detomaso
>>
>>
>> !DSPAM:5b4bb0a6259881299117678!
>> _______________________________________________
>>
>>
>> Detomaso Email List is not managed by POCA
>> Posted emails must not exceed 1.5 Megabytes
>> DeTomaso mailing list
>> [11]DeTomaso at server.detomasolist.com
>> [12]http://server.detomasolist.com/mailman/listinfo/detomaso
>>
>> To manage your subscription (change email address, unsubscribe,
etc.) use the links above.
>>
>> Members who post to this list grant license to the list to forward
any message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
>>
>> !DSPAM:5b4bb0a6259881299117678!
>
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> [13]DeTomaso at server.detomasolist.com
> [14]http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
>
> Members who post to this list grant license to the list to forward
any message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[15]DeTomaso at server.detomasolist.com
[16]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:thomas at hax.se
2. mailto:seanmundy at hotmail.com
3. mailto:bflesland at gmail.com
4. mailto:seanmundy at hotmail.com
5. mailto:DeTomaso at server.detomasolist.com
6. http://server.detomasolist.com/mailman/listinfo/detomaso
7. mailto:bflesland at gmail.com
8. mailto:seanmundy at hotmail.com
9. mailto:DeTomaso at server.detomasolist.com
10. http://server.detomasolist.com/mailman/listinfo/detomaso
11. mailto:DeTomaso at server.detomasolist.com
12. http://server.detomasolist.com/mailman/listinfo/detomaso
13. mailto:DeTomaso at server.detomasolist.com
14. http://server.detomasolist.com/mailman/listinfo/detomaso
15. mailto:DeTomaso at server.detomasolist.com
16. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list