[DeTomaso] Bay Area Guys!: Tubing bender for water pipes 1-3/8" ?????
Dave Londry
davel at emspace.com
Tue Oct 10 19:56:40 EDT 2017
If you have a bit of spare length you can send bend it.
Plenty of google and youtube examples but most techniques mess up one end.
Dave
On 10/10/2017 4:34 PM, Steve Liebenow wrote:
> OK, youse Bay area guys........I need to find someone with a 1-3/8" set
> of dies for a tubing bender.....hopefully the person with the dies has
> the tubing bender also!!! I've called all the shops I know of or that
> are still in biz......everyone starts at 1-1/2" dies and goes
> up.....roll bars etc.
> I have a new stainless thermostat housing pipe which looks like it
> should work just fine. Well, that's a matter of opinion..... It
> apparently is not an exact copy of the original. It fits on the
> engine just fine, but the outlet where it connects to the pressure tank
> is pointing off into another dimension. If I installed enough rubber
> hose, it would work......problem is that it would be crooked.....and
> I'm not into crooked.....then the pressure tank needs to be crooked,
> and the connection to the lower pipe is crooked......and so on and so
> on......
> SO, I seek a shop with the ability to tweek this sucker just a little
> bit at the 90 bend. I need it to be about an 88 or 89 degree bend so
> that it parallels the valve cover instead of heading off for the sail
> panel!
> I can't rotate it on the two mounting bolts as it is already up against
> the dipstick tube.
> Next choice, is notch it and weld it up again......not my preference
> either....but may need to go this way.......
> Lemmeno!!!!
> Thanks!
> Steve
>
>
>
> _______________________________________________
>
>
> Detomaso Email List is not managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at server.detomasolist.com
> http://server.detomasolist.com/mailman/listinfo/detomaso
>
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>
> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
If you have a bit of spare length you can send bend it.
Plenty of google and youtube examples but most techniques mess up one
end.
Dave
On 10/10/2017 4:34 PM, Steve Liebenow wrote:
OK, youse Bay area guys........I need to find someone with a 1-3/8" set
of dies for a tubing bender.....hopefully the person with the dies has
the tubing bender also!!! I've called all the shops I know of or that
are still in biz......everyone starts at 1-1/2" dies and goes
up.....roll bars etc.
I have a new stainless thermostat housing pipe which looks like it
should work just fine. Well, that's a matter of opinion..... It
apparently is not an exact copy of the original. It fits on the
engine just fine, but the outlet where it connects to the pressure tank
is pointing off into another dimension. If I installed enough rubber
hose, it would work......problem is that it would be crooked.....and
I'm not into crooked.....then the pressure tank needs to be crooked,
and the connection to the lower pipe is crooked......and so on and so
on......
SO, I seek a shop with the ability to tweek this sucker just a little
bit at the 90 bend. I need it to be about an 88 or 89 degree bend so
that it parallels the valve cover instead of heading off for the sail
panel!
I can't rotate it on the two mounting bolts as it is already up against
the dipstick tube.
Next choice, is notch it and weld it up again......not my preference
either....but may need to go this way.......
Lemmeno!!!!
Thanks!
Steve
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[1]DeTomaso at server.detomasolist.com
[2]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the li
nks above.
Members who post to this list grant license to the list to forward any message p
osted here to all past, current, or future members of the list. They also grant
the list owner permission to maintain an archive or approve the archiving of lis
t messages.
References
1. mailto:DeTomaso at server.detomasolist.com
2. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list