[DeTomaso] SS ZF linkage turnbuckle???

L GRAY tipo874a at msn.com
Mon May 22 14:56:44 EDT 2017


Chuck,
...........interesting! Well, you've done everything right on the install and assembly....... 
      I've never had the ones I installed loosen up. Maybe its my "gorilla" tightening technique !!  :-)

      Best regards,
             Leslie A. Gray

> On May 22, 2017, at 11:28 AM, "cengles at cox.net" <cengles at cox.net> wrote:
> 
> Dear Les,
> 
> 
>           I *think* that mine are well drilled.  If I drill them anymore, then I might as well go to the nuclear deterrent of drilling completely through and having the FR unit and shift rod tapped.
> 
> 
>                    Warmest regards,
> 
> PS:  I used BLUE Loctite every time I faced the FR gremlins.
> 
> 
> 
> 
> 
>> On Mon, May 22, 2017 at 11:56 AM, L GRAY wrote:
>> 
>> Mr. Chuck,
>>      I've had some experience with these replacement shift rod joints and I've noted a major improvement in shifting.  You will only notice the difference from stock units if you original joints were not articulating smoothly ( most of the originals by mow have issues where the can no longer move through their full range of motion ).
>>     The second issue of the set screws loosening, as stated previously, you MUST drill a deep enough recess where the set screw registers and then put a "dab" of BLUE Loc-Tite, then tighten the set screw appropriately. Let it set for a few hours and your all set!!!
>> 
>> Leslie A. Gray
>> 
>>> On May 22, 2017, at 8:25 AM, "cengles at cox.net" <cengles at cox.net> wrote:
>>> 
>>>  Dear Julian,
>>> 
>>>             You wrote:
>>> 
>>>   " I have heard the same comments regarding the set screw on the
>>>  Flaming river u-joints, I do prefer the through bolt design, which the
>>>  rods with the flat on the Pantera are designed for. I suspect you
>>>  really need to drill and tap for  a larger and longer set screw on the
>>>  FR joints."
>>> 
>>>           You are exactly correct.
>>> 
>>>                       Warmest regards,  Chuck Engles
>>> 
>>>>  On Mon, May 22, 2017 at 10:15 AM, Julian Kift wrote:
>>>> 
>>>> I have had good success with Midwest Control Products, they carry
>>>  large jackscrews for the adjustable camber bar. That said the
>>>  combination of stainless and large metric size probably make the rod
>>>  turnbuckle a rarity.
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> It would not be a hard item for a local fab shop to make,  a piece of
>>>  thick wall ss tubing with a couple flats machined in for a wrench and
>>>  female threads on each end. The cheaper version is weld two nuts onto a
>>>  piece of internal oversize stainless tubing.
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> I have heard the same comments regarding the set screw on the Flaming
>>>  river u-joints, I do prefer the through bolt design, which the rods
>>>  with the flat on the Pantera are designed for. I suspect you really
>>>  need to drill and tap for  a larger and longer set screw on the FR
>>>  joints.
>>> 
>>>> 
>>> 
>>>> Julian
>>> 
>>>> 
>>> 
>>>> ________________________________
>>> 
>>>> From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf
>>>  of Larry Finch via DeTomaso <detomaso at server.detomasolist.com>
>>> 
>>>> Sent: Sunday, May 21, 2017 10:08 PM
>>> 
>>>> To: Email List Address For Posting
>>> 
>>>> Subject: [DeTomaso] SS ZF linkage turnbuckle???
>>> 
>>>> 
>>> 
>>>> All,
>>> 
>>>> 
>>> 
>>>> Does anyone have a source for a stainless steel turnbuckle and
>>>  adjusting nuts for the ZF shift linkage?
>>> 
>>>> 
>>> 
>>>> I am upgrading to the stainless steel flaming river u-joints and
>>>  thought a stainless turnbuckle would be a good match.
>>> 
>>>> 
>>> 
>>>> I have searched for turnbuckle, screwjack, tie rod adjusting sleeve.
>>>  I have searched at McMaster Carr, aircraft Spruce, multiple suspension
>>>  websites, multiple Heim joint sites and I come up with nothing.
>>> 
>>>> 
>>> 
>>>> Thread size is M14x1.5  LH/RH female threads
>>> 
>>>> 
>>> 
>>>> Anyone got anything?
>>> 
>>>> 
>>> 
>>>> Larry
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> Sent from me using a magic, handheld electronic gizmo.
>>> 
>>>> _______________________________________________
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> Detomaso Email List is not managed by POCA
>>> 
>>>> Posted emails must not exceed 1.5 Megabytes
>>> 
>>>> DeTomaso mailing list
>>> 
>>>> DeTomaso at server.detomasolist.com
>>> 
>>>> http://server.detomasolist.com/mailman/listinfo/detomaso
>>> 
>>>> DeTomaso Info
>>>  Page<http://server.detomasolist.com/mailman/listinfo/detomaso>
>>> 
>>>> server.detomasolist.com
>>> 
>>>> This is the DeTomaso mailing list, a free and open forum for the
>>>  discussion of issues surrounding all DeTomaso automobiles. This is an
>>>  unmoderated mailing list ...
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> To manage your subscription (change email address, unsubscribe, etc.)
>>>  use the links above.
>>> 
>>>> 
>>> 
>>>> Members who post to this list grant license to the list to forward
>>>  any message posted here to all past, current, or future members of the
>>>  list. They also grant the list owner permission to maintain an archive
>>>  or approve the archiving of list messages.
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>>    ------------------------------
>>> 
>>>> 
>>> 
>>>> _______________________________________________
>>> 
>>>> 
>>> 
>>>> 
>>> 
>>>> Detomaso Email List is not managed by POCA
>>> 
>>>> Posted emails must not exceed 1.5 Megabytes
>>> 
>>>> DeTomaso mailing list
>>> 
>>>> DeTomaso at server.detomasolist.com
>>> 
>>>> http://server.detomasolist.com/mailman/listinfo/detomaso
>>> 
>>>> 
>>> 
>>>> To manage your subscription (change email address, unsubscribe, etc.)
>>>  use the links above.
>>> 
>>>> 
>>> 
>>>> Members who post to this list grant license to the list to forward
>>>  any message posted here to all past, current, or future members of the
>>>  list. They also grant the list owner permission to maintain an archive
>>>  or approve the archiving of list messages.
>>> _______________________________________________
>>> 
>>> 
>>> Detomaso Email List is not managed by POCA
>>> Posted emails must not exceed 1.5 Megabytes
>>> DeTomaso mailing list
>>> DeTomaso at server.detomasolist.com
>>> http://server.detomasolist.com/mailman/listinfo/detomaso
>>> 
>>> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
>>> 
>>> Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.


More information about the DeTomaso mailing list