[DeTomaso] Fluidyne sensor plugs? - Fan coming on with ignition

[Julian Kift]

I think we can all safely say that at the moment the left fan is the lower temp 😊 Anything other than that would be pure speculation as you have an aftermarket radiator with new temp sensors installed and it depends which temp sender was inserted where and then wired to which fan?


Julian

________________________________
From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf of Mike & Elizabeth Thomas <mbefthomas at comcast.net>
Sent: Saturday, December 23, 2017 1:32 PM
To: 'Corey Price'; 'Detomaso'
Subject: Re: [DeTomaso] Fluidyne sensor plugs? - Fan coming on with ignition

Have the same setup (Fluidyne rad).  The let side fan now comes on as soon as I turn on the ignition.  Likely the temp sender had failed (?) or a relay (?).  By knowing it's the left side fan, does that tell me if that's the lower or higher temp switch?

Thanks

Mike Thomas
Pres., Panteras Northwest
206-795-3302
Yellow ’74 #6328
www.panterasnorthwest.com<http://www.panterasnorthwest.com>
Panteras Northwest<http://www.panterasnorthwest.com/>
www.panterasnorthwest.com
Welcome to the Panteras Northwest website! Take a minute to meet our board of directors (below), then take some time to explore our site more fully.






-----Original Message-----
From: DeTomaso [mailto:detomaso-bounces at server.detomasolist.com] On Behalf Of Corey Price
Sent: Saturday, December 23, 2017 11:50 AM
To: Detomaso <detomaso at server.detomasolist.com>
Subject: [DeTomaso] Fluidyne sensor plugs?

I have a Fluidyne aluminum radiator and I'm looking for plugs for the temp fitting bungs.  I don't need the thermostatic switches, but I'd install the switches if I can't find plugs.

1. Does anyone know where to get some plugs for this, the size/thread of the bung, and if the bungs are tapered?
2. What are the thermostatic sensor switch part numbers?

Corey

_______________________________________________


Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso

To manage your subscription (change email address, unsubscribe, etc.) use the links above.

Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
   I think we can all safely say that at the moment the left fan is
   the lower temp  Anything other than that would be pure speculation
   as you have an aftermarket radiator with new temp sensors installed and
   it depends which temp sender was inserted where and then wired to which
   fan?

   Julian
     __________________________________________________________________

   From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf of
   Mike & Elizabeth Thomas <mbefthomas at comcast.net>
   Sent: Saturday, December 23, 2017 1:32 PM
   To: 'Corey Price'; 'Detomaso'
   Subject: Re: [DeTomaso] Fluidyne sensor plugs? - Fan coming on with
   ignition

   Have the same setup (Fluidyne rad).  The let side fan now comes on as
   soon as I turn on the ignition.  Likely the temp sender had failed (?)
   or a relay (?).  By knowing it's the left side fan, does that tell me
   if that's the lower or higher temp switch?
   Thanks
   Mike Thomas
   Pres., Panteras Northwest
   206-795-3302
   Yellow '74 #6328
   [1]www.panterasnorthwest.com
   [2]Panteras Northwest
   www.panterasnorthwest.com
   Welcome to the Panteras Northwest website! Take a minute to meet our
   board of directors (below), then take some time to explore our site
   more fully.
   -----Original Message-----
   From: DeTomaso [[3]mailto:detomaso-bounces at server.detomasolist.com] On
   Behalf Of Corey Price
   Sent: Saturday, December 23, 2017 11:50 AM
   To: Detomaso <detomaso at server.detomasolist.com>
   Subject: [DeTomaso] Fluidyne sensor plugs?
   I have a Fluidyne aluminum radiator and I'm looking for plugs for the
   temp fitting bungs.  I don't need the thermostatic switches, but I'd
   install the switches if I can't find plugs.
   1. Does anyone know where to get some plugs for this, the size/thread
   of the bung, and if the bungs are tapered?
   2. What are the thermostatic sensor switch part numbers?
   Corey
   _______________________________________________
   Detomaso Email List is not managed by POCA
   Posted emails must not exceed 1.5 Megabytes
   DeTomaso mailing list
   DeTomaso at server.detomasolist.com
   [4]http://server.detomasolist.com/mailman/listinfo/detomaso
   To manage your subscription (change email address, unsubscribe, etc.)
   use the links above.
   Members who post to this list grant license to the list to forward any
   message posted here to all past, current, or future members of the
   list. They also grant the list owner permission to maintain an archive
   or approve the archiving of list messages.

References

   1. http://www.panterasnorthwest.com/
   2. http://www.panterasnorthwest.com/
   3. mailto:detomaso-bounces at server.detomasolist.com
   4. http://server.detomasolist.com/mailman/listinfo/detomaso