[DeTomaso] stock A arm bushing quaility ?
B Hower
b.hower3400 at yahoo.com
Sat Aug 19 21:34:33 EDT 2017
Lolita came to me with after market Poly ? bushings.......of which the ID was to be installed over the mounting bolts ( now sleeve/spindle ). Therefore they could be pinched between mounting tabs. I was told by a vendor that they were worse than OEM for handling. Bud #3400 ( Drive it like there is no tomorrow -- for there may not be ! )
From: "Joseph F. Byrd, Jr." <byrdjf at embarqmail.com>
To: detomaso at server.detomasolist.com
Sent: Saturday, August 19, 2017 8:23 PM
Subject: [DeTomaso] stock A arm bushing quaility ?
During the chassis discussion, I discovered the quality of the "stock"
A arm bushings I just received might be less than desired.
The frame drawing shows the tabs should be 47mm or 1.850" +0.020/-0.
I checked 4 of my removed A arms and yes the bushings are 1.850 +/-
0.005 (the tolerance of quickly checking with calipers)
However I checked 8 of the 16 new ones and they were 1.850 +/- 0.50".
Yes, the ranged from 1.80 to 1.90!
Did I receive rejects? L
Or is this just a car and not rocket science.
Joe
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
Lolita came to me with after market Poly ? bushings.......of which the
ID was to be installed over the mounting bolts ( now sleeve/spindle ).
Therefore they could be pinched between mounting tabs. I was told by a
vendor that they were worse than OEM for handling.
Bud #3400 ( Drive it like there is no tomorrow -- for there may not be
! )
__________________________________________________________________
From: "Joseph F. Byrd, Jr." <byrdjf at embarqmail.com>
To: detomaso at server.detomasolist.com
Sent: Saturday, August 19, 2017 8:23 PM
Subject: [DeTomaso] stock A arm bushing quaility ?
During the chassis discussion, I discovered the quality of the
"stock"
A arm bushings I just received might be less than desired.
The frame drawing shows the tabs should be 47mm or 1.850" +0.020/-0.
I checked 4 of my removed A arms and yes the bushings are 1.850 +/-
0.005 (the tolerance of quickly checking with calipers)
However I checked 8 of the 16 new ones and they were 1.850 +/-
0.50".
Yes, the ranged from 1.80 to 1.90!
Did I receive rejects? L
Or is this just a car and not rocket science.
Joe
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[1]DeTomaso at server.detomasolist.com
[2]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:DeTomaso at server.detomasolist.com
2. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list