[DeTomaso] Pedal Casting?
mark skwarek
ehpantera at yahoo.com
Sat Apr 1 15:08:05 EDT 2017
If you are converting the stock pedal assembly to non vacuum assisted, the pedal effort will increase. Willwood manual pedal assy. is 6:1 and power brakes are between 5:1 and 4:1.
Mark
On Thursday, March 30, 2017 6:33 PM, Ken Green via DeTomaso <detomaso at server.detomasolist.com> wrote:
Hi Les,
Any idea what you would want for the pedal assembly casting?
I used a Tilton 7/16 balance bar on the prototype, and it placed
the MC shafts where some of the webbing is on the pedal side, so I had
to cut into the webbing. I found a 1/2 inch Tilton balance bar and it
is wider, so I can avoid the webbing. I did basically the same as
Goran did before me (see attachment). I like this a lot better than
something that is in front of the casting, I think Dennis Quela has
something like that.
So you are back in California?
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
__________________________________________________________________
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
If you are converting the stock pedal assembly to non vacuum assisted,
the pedal effort will increase. Willwood manual pedal assy. is 6:1 and
power brakes are between 5:1 and 4:1.
Mark
On Thursday, March 30, 2017 6:33 PM, Ken Green via DeTomaso
<detomaso at server.detomasolist.com> wrote:
Hi Les,
Any idea what you would want for the pedal assembly casting?
I used a Tilton 7/16 balance bar on the prototype, and it placed
the MC shafts where some of the webbing is on the pedal side, so I
had
to cut into the webbing. I found a 1/2 inch Tilton balance bar and
it
is wider, so I can avoid the webbing. I did basically the same as
Goran did before me (see attachment). I like this a lot better than
something that is in front of the casting, I think Dennis Quela has
something like that.
So you are back in California?
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
Inline image
__________________________________________________________________
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[1]DeTomaso at server.detomasolist.com
[2]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:DeTomaso at server.detomasolist.com
2. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list