[DeTomaso] FW: Harbor Fright Engine Support Bar
Julian Kift
julian_kift at hotmail.com
Sun Nov 20 22:22:10 EST 2016
I have done this numerous times on early cars, never have I removed the decklid, loosened the mufflers or drained any coolant.
On the 9000 series the chassis side ZF mounting ears are removable, which makes it even easier.
Julian
________________________________
From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf of Mike Thomas <mbefthomas at comcast.net>
Sent: Sunday, November 20, 2016 7:18 PM
To: 'De Tomaso List'
Subject: [DeTomaso] FW: Harbor Fright Engine Support Bar
You also need to drain some of the cooling as tilting the engine forward requires disconnecting the upper pressure tank hose.
Other than that, it's:
- Remove the deck lid
- Remove and set aside the clutch slave
- Remove the starter
- Disconnect the shift linkage and half-shafts
- Remove the two bolts holding the bottom of the rear engine cover to the bell housing
- Disconnect the headers from the exhaust pipes (to allow the engine to tilt)
- Disconnect the speedo cable
- Disconnect the ground connection at the back of the ZF
- Disconnect the backup light switch from the shifter box
Mike
-----Original Message-----
From: DeTomaso [mailto:detomaso-bounces at server.detomasolist.com] On Behalf Of B Hower via DeTomaso
Sent: Sunday, November 20, 2016 6:36 PM
To: MikeLDrew at aol.com; byrdjf at embarqmail.com
Cc: detomaso at server.detomasolist.com
Subject: Re: [DeTomaso] Harbor Fright Engine Support Bar
If all OEM bolts are installed one has to pull the bell housing which means removing the starter also. IIRC
Bud #3400 ( Drive it like there is no tomorrow -- for there may not be ! )
From: Mike Drew via DeTomaso <detomaso at server.detomasolist.com>
To: byrdjf at embarqmail.com
Cc: detomaso at server.detomasolist.com
Sent: Sunday, November 20, 2016 8:12 PM
Subject: Re: [DeTomaso] Harbor Fright Engine Support Bar
In a message dated 11/20/16 17 14 34, byrdjf at embarqmail.com writes:
How much has to be loosen/removed on the engine to tilt it? just
the motor
mounts?
>>>Well, naturally the gearbox has to be free to lift up. That means
disconnecting the shift linkage from the gearbox, as well as the
driveshafts and the clutch slave cylinder/bracket/etc., and removing
the bolts that connect the gearbox mounts to the chassis. Assuming you
want to remove the gearbox, you have to unbolt the A/C condenser/fan
assembly, and hang them off the right rear corner of the car by the A/C
hoses (naturally you would lay towels etc. over the body to protect
it). You would also have to either loosen or remove the bolts holding
the mufflers to the headers (wrap the mufflers with towels to prevent
them from scratching the paint as well).
Then the gearbox slides right out. Getting it back in can be either
easy or difficult...there's no sure-fire way to ensure it all goes in
right way the first time--there's a lot of fiddling around to get the
angles just right. But once everything is right, it just snicks right
into place.
Mike
_______________________________________________
Detomaso Email List is not managed by POCA Posted emails must not exceed 1.5 Megabytes DeTomaso mailing list DeTomaso at server.detomasolist.com http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.
-------------- next part --------------
I have done this numerous times on early cars, never have I removed the
decklid, loosened the mufflers or drained any coolant.
On the 9000 series the chassis side ZF mounting ears are removable,
which makes it even easier.
Julian
__________________________________________________________________
From: DeTomaso <detomaso-bounces at server.detomasolist.com> on behalf of
Mike Thomas <mbefthomas at comcast.net>
Sent: Sunday, November 20, 2016 7:18 PM
To: 'De Tomaso List'
Subject: [DeTomaso] FW: Harbor Fright Engine Support Bar
You also need to drain some of the cooling as tilting the engine
forward requires disconnecting the upper pressure tank hose.
Other than that, it's:
- Remove the deck lid
- Remove and set aside the clutch slave
- Remove the starter
- Disconnect the shift linkage and half-shafts
- Remove the two bolts holding the bottom of the rear engine cover to
the bell housing
- Disconnect the headers from the exhaust pipes (to allow the engine to
tilt)
- Disconnect the speedo cable
- Disconnect the ground connection at the back of the ZF
- Disconnect the backup light switch from the shifter box
Mike
-----Original Message-----
From: DeTomaso [[1]mailto:detomaso-bounces at server.detomasolist.com] On
Behalf Of B Hower via DeTomaso
Sent: Sunday, November 20, 2016 6:36 PM
To: MikeLDrew at aol.com; byrdjf at embarqmail.com
Cc: detomaso at server.detomasolist.com
Subject: Re: [DeTomaso] Harbor Fright Engine Support Bar
If all OEM bolts are installed one has to pull the bell housing which
means removing the starter also. IIRC
Bud #3400 ( Drive it like there is no tomorrow -- for there may not be
! )
From: Mike Drew via DeTomaso <detomaso at server.detomasolist.com>
To: byrdjf at embarqmail.com
Cc: detomaso at server.detomasolist.com
Sent: Sunday, November 20, 2016 8:12 PM
Subject: Re: [DeTomaso] Harbor Fright Engine Support Bar
In a message dated 11/20/16 17 14 34, byrdjf at embarqmail.com writes:
How much has to be loosen/removed on the engine to tilt it? just
the motor
mounts?
>>>Well, naturally the gearbox has to be free to lift up. That means
disconnecting the shift linkage from the gearbox, as well as the
driveshafts and the clutch slave cylinder/bracket/etc., and removing
the bolts that connect the gearbox mounts to the chassis. Assuming
you
want to remove the gearbox, you have to unbolt the A/C condenser/fan
assembly, and hang them off the right rear corner of the car by the
A/C
hoses (naturally you would lay towels etc. over the body to protect
it). You would also have to either loosen or remove the bolts
holding
the mufflers to the headers (wrap the mufflers with towels to prevent
them from scratching the paint as well).
Then the gearbox slides right out. Getting it back in can be either
easy or difficult...there's no sure-fire way to ensure it all goes in
right way the first time--there's a lot of fiddling around to get the
angles just right. But once everything is right, it just snicks
right
into place.
Mike
_______________________________________________
Detomaso Email List is not managed by POCA Posted emails must not
exceed 1.5 Megabytes DeTomaso mailing list
DeTomaso at server.detomasolist.com
[2]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
_______________________________________________
Detomaso Email List is not managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at server.detomasolist.com
[3]http://server.detomasolist.com/mailman/listinfo/detomaso
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
Members who post to this list grant license to the list to forward any
message posted here to all past, current, or future members of the
list. They also grant the list owner permission to maintain an archive
or approve the archiving of list messages.
References
1. mailto:detomaso-bounces at server.detomasolist.com
2. http://server.detomasolist.com/mailman/listinfo/detomaso
3. http://server.detomasolist.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list