[DeTomaso] Pictures

Timothy Meyer fordmachinist at gmail.com
Fri Mar 18 16:06:31 EDT 2016 

Thanks All.

This has no doubt be a labor of love…

Feel free to contact me anytime and I would be glad to help.

At this point there are a few details that we are not sharing, 

we have some features that have not been seen or used on an automotive block.

 

One hint…

Eck Industries is the foundry that is casting our aluminum block.

Eck Industries is also the foundry that made the engine block that was in the mid 2000’s Ford GT (2005-2006) I think.

 



 

From: jderyke at aol.com [mailto:jderyke at aol.com] 
Sent: Friday, March 18, 2016 2:16 PM
To: fordmachinist at gmail.com
Cc: detomaso at poca.com
Subject: Re: [DeTomaso] Pictures

 

Good deal, Tim! I saw the shots you recently posted on the Engine Builders Forum of your #1 aluminum casting. Tim showed the unmachined casting, then SAWED IT UP to check internal integrity! Certainly looks robust enough to handle rather high horsepower, with thick walls everywhere.  I'd love to publish a detailed article in the POCA Newsletter, with photos, at your convenience. Tim's block is an upgrade from the 3-4 examples cast by previous project owner Tod Butterworth and machined by Barry Robotnik just as Tod ran out of money and motivation to continue.
J DeRyke

 

 

-----Original Message-----
On Fri, Mar 18, 2016 at 11:16 AM, Timothy Meyer
<[1]fordmachinist at gmail.com <mailto:fordmachinist at gmail.com> > wrote:

A A I would like to share pictures of our new Cleveland block.
A A Am I allowed to do that, and how can I attach them if I am
allowed?
A A email sig
_______________________________________________
Detomaso Forum Managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[2]DeTomaso at poca.com <mailto:DeTomaso at poca.com> 
[3]http://poca.com/mailman/listinfo/detomaso_poca.com
To manage your subscription (change email address, unsubscribe,
etc.) use the links above.

--
Michael L. Shortt
Savannah, Georgia
[4]www.michaelshortt.com <http://www.michaelshortt.com> 
[5]michael at michaelshortt.com <mailto:michael at michaelshortt.com> 
912-232-9390
A
This email is protected by the Electronic Communications Privacy
Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
privileged.A If you are not the intended recipient, you are hereby
notified
that any retention, dissemination, distribution or copying of this
communication is strictly prohibited.A Please reply to the sender that
you
have received this message in error, then delete it.A Thank you

References

1. mailto:fordmachinist at gmail.com <mailto:fordmachinist at gmail.com?> 
2. mailto:DeTomaso at poca.com <mailto:DeTomaso at poca.com?> 
3. http://poca.com/mailman/listinfo/detomaso_poca.com
4. http://www.michaelshortt.com/
5. mailto:michael at michaelshortt.com <mailto:michael at michaelshortt.com?> 
_______________________________________________

Detomaso Forum Managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at poca.com <mailto:DeTomaso at poca.com> 
http://poca.com/mailman/listinfo/detomaso_poca.com

To manage your subscription (change email address, unsubscribe, etc.) use the links above.

  _____  

No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com> 
Version: 2016.0.7497 / Virus Database: 4542/11836 - Release Date: 03/18/16

-------------- next part --------------
   Thanks All.

   This has no doubt be a labor of love...

   Feel free to contact me anytime and I would be glad to help.

   At this point there are a few details that we are not sharing,

   we have some features that have not been seen or used on an automotive
   block.


   One hint...

   Eck Industries is the foundry that is casting our aluminum block.

   Eck Industries is also the foundry that made the engine block that was
   in the mid 2000's Ford GT (2005-2006) I think.


   email sig


   From: jderyke at aol.com [mailto:jderyke at aol.com]
   Sent: Friday, March 18, 2016 2:16 PM
   To: fordmachinist at gmail.com
   Cc: detomaso at poca.com
   Subject: Re: [DeTomaso] Pictures


   Good deal, Tim! I saw the shots you recently posted on the Engine
   Builders Forum of your #1 aluminum casting. Tim showed the unmachined
   casting, then SAWED IT UP to check internal integrity! Certainly looks
   robust enough to handle rather high horsepower, with thick walls
   everywhere.  I'd love to publish a detailed article in the POCA
   Newsletter, with photos, at your convenience. Tim's block is an upgrade
   from the 3-4 examples cast by previous project owner Tod Butterworth
   and machined by Barry Robotnik just as Tod ran out of money and
   motivation to continue.
   J DeRyke



   -----Original Message-----
   On Fri, Mar 18, 2016 at 11:16 AM, Timothy Meyer
   <[1][1]fordmachinist at gmail.com> wrote:
   A A I would like to share pictures of our new Cleveland block.
   A A Am I allowed to do that, and how can I attach them if I am
   allowed?
   A A email sig
   _______________________________________________
   Detomaso Forum Managed by POCA
   Posted emails must not exceed 1.5 Megabytes
   DeTomaso mailing list
   [2][2]DeTomaso at poca.com
   [3][3]http://poca.com/mailman/listinfo/detomaso_poca.com
   To manage your subscription (change email address, unsubscribe,
   etc.) use the links above.
   --
   Michael L. Shortt
   Savannah, Georgia
   [4][4]www.michaelshortt.com
   [5][5]michael at michaelshortt.com
   912-232-9390
   A
   This email is protected by the Electronic Communications Privacy
   Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
   privileged.A If you are not the intended recipient, you are hereby
   notified
   that any retention, dissemination, distribution or copying of this
   communication is strictly prohibited.A Please reply to the sender that
   you
   have received this message in error, then delete it.A Thank you
   References
   1. [6]mailto:fordmachinist at gmail.com
   2. [7]mailto:DeTomaso at poca.com
   3. [8]http://poca.com/mailman/listinfo/detomaso_poca.com
   4. [9]http://www.michaelshortt.com/
   5. [10]mailto:michael at michaelshortt.com
   _______________________________________________
   Detomaso Forum Managed by POCA
   Posted emails must not exceed 1.5 Megabytes
   DeTomaso mailing list
   [11]DeTomaso at poca.com
   [12]http://poca.com/mailman/listinfo/detomaso_poca.com
   To manage your subscription (change email address, unsubscribe, etc.)
   use the links above.
   _______________________________________________________________________

   No virus found in this message.
   Checked by AVG - [13]www.avg.com
   Version: 2016.0.7497 / Virus Database: 4542/11836 - Release Date:
   03/18/16

References

   1. mailto:fordmachinist at gmail.com
   2. mailto:DeTomaso at poca.com
   3. http://poca.com/mailman/listinfo/detomaso_poca.com
   4. http://www.michaelshortt.com/
   5. mailto:michael at michaelshortt.com
   6. mailto:fordmachinist at gmail.com?
   7. mailto:DeTomaso at poca.com?
   8. http://poca.com/mailman/listinfo/detomaso_poca.com
   9. http://www.michaelshortt.com/
  10. mailto:michael at michaelshortt.com?
  11. mailto:DeTomaso at poca.com
  12. http://poca.com/mailman/listinfo/detomaso_poca.com
  13. http://www.avg.com/
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image003.jpg
Type: image/jpeg
Size: 12757 bytes
Desc: not available
URL: <http://server.detomasolist.com/pipermail/detomaso/attachments/20160318/765773ee/attachment.jpg>

More information about the DeTomaso mailing list