[DeTomaso] Battery Tie Down Tray for Optima

Rob Dumoulin rob at dumoulins.net
Tue Mar 8 14:49:34 EST 2016


Yup, too late to weld in a bracket. Trunk already painted.  The stock
tie-down bar I have would be way too long for an optima anyhow.

A nice leather strap mounted from the back going horizontal would be OK.  I
think I would want one vertical too to stop battery from slipping upwards.

I had option 4 before and did not care for it.  I filled the holes prior to
paint.

Rob DuMoulin
904.476.8744
rob at dumoulins.net
www.kbsi.co
http://www.linkedin.com/pub/rob-dumoulin/0/1b6/58

On Tue, Mar 8, 2016 at 2:22 PM, Michael Shortt <michaelsavga at gmail.com>
wrote:

> Is it too late to braze a new bracket where it belongs?
>
> If not, I have a spare battery hold down set up.
>
> Option two would be to install other hold down system with sheet metal
> screws
> and I'd probably pick one with a wide footprint flange and also use J/B
> Weld on the bottom.
>
> Option three could be a sideways strap that attaches to the firewall
> behind the battery instead of the floor below the battery.
>
> Option four are those little clip style hold downs that just grip the lip
> on the base of the battery.
> those would also have to be mounted with bolts, plastic welding or brazing.
>
> Michael Shortt
>
>
>
>
>
> I
>
> On Tue, Mar 8, 2016 at 1:58 PM, Rob Dumoulin <rob at dumoulins.net> wrote:
>
>>    For the Optima batteries, what are some of the ways you have tied them
>>    down. I bought a nice billet tray that I though would work but the bars
>>    holding down the battery on in the front and back rather than side to
>>    side and it protrudes too far out into the trunk.A  I could try a
>>    side-to-side one, but wanted to get some first hand knowledge from the
>>    collective.
>>    BTW, one of my stock brackets was never on the car, so I could never
>>    use the traditional approach.
>>    Any recommendations?
>>
>> _______________________________________________
>>
>> Detomaso Forum Managed by POCA
>> Posted emails must not exceed 1.5 Megabytes
>> DeTomaso mailing list
>> DeTomaso at poca.com
>> http://poca.com/mailman/listinfo/detomaso_poca.com
>>
>> To manage your subscription (change email address, unsubscribe, etc.) use
>> the links above.
>>
>>
>
>
> --
>
>
>
>
>
>
>
> Michael L. Shortt
> Savannah, Georgia
> www.michaelshortt.com
> michael at michaelshortt.com
> 912-232-9390
>
>
> This email is protected by the Electronic Communications Privacy
> Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
> privileged.  If you are not the intended recipient, you are hereby notified
> that any retention, dissemination, distribution or copying of this
> communication is strictly prohibited.  Please reply to the sender that you
> have received this message in error, then delete it.  Thank you
>
-------------- next part --------------
   Yup, too late to weld in a bracket. Trunk already painted.A  The stock
   tie-down bar I have would be way too long for an optima anyhow. A
   A nice leather strap mounted from the back going horizontal would be
   OK.A  I think I would want one vertical too to stop battery from
   slipping upwards.
   I had option 4 before and did not care for it.A  I filled the holes
   prior to paint.
   Rob DuMoulin
   904.476.8744
   [1]rob at dumoulins.net
   [2]www.kbsi.co
   [3]http://www.linkedin.com/pub/rob-dumoulin/0/1b6/58
   On Tue, Mar 8, 2016 at 2:22 PM, Michael Shortt
   <[4]michaelsavga at gmail.com> wrote:

   Is it too late to braze a new bracket where it belongs?
   If not, I have a spare battery hold down set up.
   Option two would be to install other hold down system with sheet metal
   screws
   and I'd probably pick one with a wide footprint flange and also use J/B
   Weld on the bottom.
   Option three could be a sideways strap that attaches to the firewall
   behind the battery instead of the floor below the battery.
   Option four are those little clip style hold downs that just grip the
   lip on the base of the battery.
   those would also have to be mounted with bolts, plastic welding or
   brazing.
   Michael Shortt
   I

   On Tue, Mar 8, 2016 at 1:58 PM, Rob Dumoulin <[5]rob at dumoulins.net>
   wrote:

     A  A For the Optima batteries, what are some of the ways you have
     tied them
     A  A down. I bought a nice billet tray that I though would work but
     the bars
     A  A holding down the battery on in the front and back rather than
     side to
     A  A side and it protrudes too far out into the trunk.AA  I could
     try a
     A  A side-to-side one, but wanted to get some first hand knowledge
     from the
     A  A collective.
     A  A BTW, one of my stock brackets was never on the car, so I could
     never
     A  A use the traditional approach.
     A  A Any recommendations?
     _______________________________________________
     Detomaso Forum Managed by POCA
     Posted emails must not exceed 1.5 Megabytes
     DeTomaso mailing list
     [6]DeTomaso at poca.com
     [7]http://poca.com/mailman/listinfo/detomaso_poca.com
     To manage your subscription (change email address, unsubscribe,
     etc.) use the links above.

   --
   Michael L. Shortt
   Savannah, Georgia
   [8]www.michaelshortt.com
   [9]michael at michaelshortt.com
   [10]912-232-9390
   A
   This email is protected by the Electronic Communications Privacy
   Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
   privileged.A  If you are not the intended recipient, you are hereby
   notified
   that any retention, dissemination, distribution or copying of this
   communication is strictly prohibited.A  Please reply to the sender that
   you
   have received this message in error, then delete it.A  Thank you

References

   1. mailto:rob at dumoulins.net
   2. http://www.kbsi.co/
   3. http://www.linkedin.com/pub/rob-dumoulin/0/1b6/58
   4. mailto:michaelsavga at gmail.com
   5. mailto:rob at dumoulins.net
   6. mailto:DeTomaso at poca.com
   7. http://poca.com/mailman/listinfo/detomaso_poca.com
   8. http://www.michaelshortt.com/
   9. mailto:michael at michaelshortt.com
  10. tel:912-232-9390


More information about the DeTomaso mailing list