[DeTomaso] Rear quarter vents

Ed Mendez edducati at mac.com
Sat Oct 10 13:48:00 EDT 2015


Thanks

Sent from my iPhone 6 Plus

> On 10/10/2015, at 9:44 AM, B Hower <b.hower3400 at yahoo.com> wrote:
> 
> FWIW: Mine are M5-.80 see attached photo of bag in witch the wing nuts came. I had no missing studs.
>  
> Bud #3400 ( Drive it like there is no tomorrow -- for there may not be ! )
> 
> ----- Forwarded Message -----
> From: Ed Mendez <edducati at mac.com>
> To: "detomaso at poca.com" <detomaso at poca.com> 
> Sent: Friday, October 9, 2015 10:47 PM
> Subject: [DeTomaso] Rear quarter vents
> 
> Anyone have a picture of the back side of the rear quarter decorative vents? And what is the thread size on the 4 mounting posts supposed to be? 6-8mm? x ?
> 
> If the threads on the posts are stripped; it appears to be pot metal, what can you use to fill the holes and re-drill and tap the new threads? JB Weld?
> 
> Thanks Ed
> 
> Sent from my iPhone 6 Plus
> _______________________________________________
> 
> Detomaso Forum Managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at poca.com
> http://poca.com/mailman/listinfo/detomaso_poca.com
> 
> To manage your subscription (change email address, unsubscribe, etc.) use the links above.
> 
> 
> <gill wing nuts.jpg>
-------------- next part --------------
   Thanks
   Sent from my iPhone 6 Plus

   On 10/10/2015, at 9:44 AM, B Hower <[1]b.hower3400 at yahoo.com> wrote:

   FWIW: Mine are M5-.80 see attached photo of bag in witch the wing nuts
   came. I had no missing studs.

   Bud #3400 ( Drive it like there is no tomorrow -- for there may not be
   ! )
   ----- Forwarded Message -----
   From: Ed Mendez <[2]edducati at mac.com>
   To: "[3]detomaso at poca.com" <[4]detomaso at poca.com>
   Sent: Friday, October 9, 2015 10:47 PM
   Subject: [DeTomaso] Rear quarter vents
   Anyone have a picture of the back side of the rear quarter decorative
   vents? And what is the thread size on the 4 mounting posts supposed to
   be? 6-8mm? x ?
   If the threads on the posts are stripped; it appears to be pot metal,
   what can you use to fill the holes and re-drill and tap the new
   threads? JB Weld?
   Thanks Ed
   Sent from my iPhone 6 Plus
   _______________________________________________
   Detomaso Forum Managed by POCA
   Posted emails must not exceed 1.5 Megabytes
   DeTomaso mailing list
   [5]DeTomaso at poca.com
   [6]http://poca.com/mailman/listinfo/detomaso_poca.com
   To manage your subscription (change email address, unsubscribe, etc.)
   use the links above.

   <gill wing nuts.jpg>

References

   1. mailto:b.hower3400 at yahoo.com
   2. mailto:edducati at mac.com
   3. mailto:detomaso at poca.com
   4. mailto:detomaso at poca.com
   5. mailto:DeTomaso at poca.com
   6. http://poca.com/mailman/listinfo/detomaso_poca.com


More information about the DeTomaso mailing list