[DeTomaso] Hood measurement

[Michael Shortt]

I can provide it tonight when I get home.

Michael Shortt


On Mon, Nov 9, 2015 at 10:18 AM, Lynn Wall <lwall67 at gmail.com> wrote:

>    All,
>
>
>    Can anyone with an un-molested car provide a dimension to me?  I'm
>    looking for the width of the hood opening as measured across the hinge
>    plate.  By hood opening I'm talking about the recessed area that the
>    hood rests in.   My car was crunched hard in this area and I'm trying
>    to confirm dimensions as part of the repair process.  With fenders on
>    and straight my hinge plate appears to be about 3/8 of an inch short of
>    the width.
>
>
>    Corey gave me a dimension of 32" but since his car suffered damage in
>    the same area I'm not sure if that is a reliable width.
>
>
>    Thanks, Lynn
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
> Posted emails must not exceed 1.5 Megabytes
> DeTomaso mailing list
> DeTomaso at poca.com
> http://poca.com/mailman/listinfo/detomaso_poca.com
>
> To manage your subscription (change email address, unsubscribe, etc.) use
> the links above.
>
>


-- 







Michael L. Shortt
Savannah, Georgia
www.michaelshortt.com
michael at michaelshortt.com
912-232-9390


This email is protected by the Electronic Communications Privacy
Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
privileged.  If you are not the intended recipient, you are hereby notified
that any retention, dissemination, distribution or copying of this
communication is strictly prohibited.  Please reply to the sender that you
have received this message in error, then delete it.  Thank you
-------------- next part --------------
   I can provide it tonight when I get home.
   Michael Shortt

   On Mon, Nov 9, 2015 at 10:18 AM, Lynn Wall <[1]lwall67 at gmail.com>
   wrote:

     A  A All,
     A  A Can anyone with an un-molested car provide a dimension to me?A
     I'm
     A  A looking for the width of the hood opening as measured across
     the hinge
     A  A plate.A  By hood opening I'm talking about the recessed area
     that the
     A  A hood rests in.A  A My car was crunched hard in this area and
     I'm trying
     A  A to confirm dimensions as part of the repair process.A  With
     fenders on
     A  A and straight my hinge plate appears to be about 3/8 of an inch
     short of
     A  A the width.
     A  A Corey gave me a dimension of 32" but since his car suffered
     damage in
     A  A the same area I'm not sure if that is a reliable width.
     A  A Thanks, Lynn
     _______________________________________________
     Detomaso Forum Managed by POCA
     Posted emails must not exceed 1.5 Megabytes
     DeTomaso mailing list
     [2]DeTomaso at poca.com
     [3]http://poca.com/mailman/listinfo/detomaso_poca.com
     To manage your subscription (change email address, unsubscribe,
     etc.) use the links above.

   --
   Michael L. Shortt
   Savannah, Georgia
   [4]www.michaelshortt.com
   [5]michael at michaelshortt.com
   912-232-9390
   A
   This email is protected by the Electronic Communications Privacy
   Act, 18 U.S.C. Sec. 2510-2521, is confidential and may be legally
   privileged.A  If you are not the intended recipient, you are hereby
   notified
   that any retention, dissemination, distribution or copying of this
   communication is strictly prohibited.A  Please reply to the sender that
   you
   have received this message in error, then delete it.A  Thank you

References

   1. mailto:lwall67 at gmail.com
   2. mailto:DeTomaso at poca.com
   3. http://poca.com/mailman/listinfo/detomaso_poca.com
   4. http://www.michaelshortt.com/
   5. mailto:michael at michaelshortt.com