[DeTomaso] Rocker Arms
mark skwarek
ehpantera at yahoo.com
Sun Mar 8 22:33:30 EDT 2015
Just make sure that you have clearance between the pushrod and the rocker base at full lift. Under high lift the pushrod can make contact with the base of the rocker arm. Them the end of the rocker arm end will break off. Been there, done that.
Mark
On Sunday, March 8, 2015 9:48 PM, doug351c <doug351c at gmail.com> wrote:
I like the Scorpion Endurance SCP3023 1.73:1 forged aluminum roller rockers.
They have a hardened insert seat, the shaft is centerless ground, a 7/16"
poloc nut is included and they have a great lifetime warranty. $326 a set
at Summit Racing.
Max spring dia = 1.625"
http://www.summitracing.com/parts/scc-scp3023bl
I'm running these on my 70 Cleveland Mach1 engine. Please note though that
if you intend to run 7/16" dia pushrods, their backsides need to be
clearance for them. Scorpion's Endurance series cost more than the Race
series but they have a narrower body and shorter polylocks so they fit
better under stock rocker covers.
Doug Braun
blue 73L #550
-----Original Message-----
From: DeTomaso [mailto:detomaso-bounces at poca.com]On Behalf Of Tony
DiGiovanna
Sent: Sunday, March 08, 2015 4:00 PM
To: detomaso at poca.com
Subject: [DeTomaso] Rocker Arms
351C, solid flat tappet cam with lift of 0.640. 7/16 screwed-in studs. Any
opinions on Rock Arms? PRW vs. Harland Sharp vs. other?
_______________________________________________
Detomaso Forum Managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
DeTomaso at poca.com
http://poca.com/mailman/listinfo/detomaso_poca.com
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
-------------- next part --------------
Just make sure that you have clearance between the pushrod and the
rocker base at full lift. Under high lift the pushrod can make contact
with the base of the rocker arm. Them the end of the rocker arm end
will break off. Been there, done that.
Mark
On Sunday, March 8, 2015 9:48 PM, doug351c <doug351c at gmail.com> wrote:
I like the Scorpion Endurance SCP3023 1.73:1 forged aluminum roller
rockers.
They have a hardened insert seat, the shaft is centerless ground, a
7/16"
poloc nut is included and they have a great lifetime warranty. $326 a
set
at Summit Racing.
Max spring dia = 1.625"
[1]http://www.summitracing.com/parts/scc-scp3023bl
I'm running these on my 70 Cleveland Mach1 engine. Please note though
that
if you intend to run 7/16" dia pushrods, their backsides need to be
clearance for them. Scorpion's Endurance series cost more than the
Race
series but they have a narrower body and shorter polylocks so they fit
better under stock rocker covers.
Doug Braun
blue 73L #550
-----Original Message-----
From: DeTomaso [mailto:[2]detomaso-bounces at poca.com]On Behalf Of Tony
DiGiovanna
Sent: Sunday, March 08, 2015 4:00 PM
To: [3]detomaso at poca.com
Subject: [DeTomaso] Rocker Arms
351C, solid flat tappet cam with lift of 0.640. 7/16 screwed-in
studs. Any
opinions on Rock Arms? PRW vs. Harland Sharp vs. other?
_______________________________________________
Detomaso Forum Managed by POCA
Posted emails must not exceed 1.5 Megabytes
DeTomaso mailing list
[4]DeTomaso at poca.com
[5]http://poca.com/mailman/listinfo/detomaso_poca.com
To manage your subscription (change email address, unsubscribe, etc.)
use the links above.
References
1. file://localhost/tmp/tmpzLOGfU.html
2. file://localhost/tmp/tmpzLOGfU.html
3. file://localhost/tmp/tmpzLOGfU.html
4. file://localhost/tmp/tmpzLOGfU.html
5. file://localhost/tmp/tmpzLOGfU.html
More information about the DeTomaso
mailing list