[DeTomaso] A 351C (and other stuff) for sale

[Kirby Schrader]

No… most definitely not.
Too much stuff in my garage which is doing nothing…. and funding a new engine for the race car.

On Mar 13, 2014, at 22:20, Bill Moore <bill at incendium.com> wrote:

> What's going on, are you moving? 
> Bill Moore
> Incendium Supply
> Calgary
> 
> -----Original Message-----
> From: Kirby Schrader <kirby.schrader at gmail.com>
> Sender: "DeTomaso" <detomaso-bounces at poca.com>Date: Thu, 13 Mar 2014 21:33:47 
> To: detomaso mail list<DeTomaso at poca.com>
> Cc: Space City Panteras<SCPOCA at yahoogroups.com>
> Subject: Re: [DeTomaso] A 351C (and other stuff) for sale
> 
> 
> A slight correction…
> 
> One oil pan is steel, the other is aluminum. Both used.
> Whichever sells first get the aluminum one and the steel one goes with the engine…
> or…
> the other way around…
> How’s that for confusing?
> But I think you know what I mean….
> 
>> 
>> On Mar 13, 2014, at 8:15 PM, Kirby Schrader <kirby.schrader at gmail.com> wrote:
>> 
>> I have a Cleveland motor that I will not be using in addition to other
>> engine parts that I'd like to sell.
>> It's all for a good cause...
>> 351C
>>  - Cleveland block .030 over
>>  - Nodular iron stock crankshaft - stock, but I'm told `it's the good
>> one' whatever that means (D4AE something?)
>>    I can get the number if you need it
>>  - Eagle rods
>>  - TRW popup pistons
>>  - 10qt aluminum oil pan
>>  - C302B heads and intake (they have not been milled or ported as far
>> as I can tell)
>>  - Solid roller cam and lifters
>>  - Roller rockers
>>  - MSD distributor
>> Comments:
>> This motor was running when it was pulled out of the car. (a bigger,
>> better, badder one was installed)
>> It had been recently rebuilt with new rings and bearings.
>> Pulled the intake and heads and pan just to check things out. All looks
>> good.
>> It will only run on racegas with those popup pistons.
>> I know nothing about the cam specs nor the valves or springs.
>> Three of the roller rockers were replaced at some time in the past.. I
>> don't know why.
>> Yes, it's .030 over, but it was running good. I believe it to be a
>> good, solid block.
>> Location: Magnolia, Texas
>> Pictures on request
>> $2750
>> Other stuff
>>  - 351C 6268-A351 Roller timing chain set - Ford Motorsports - new
>> $100 plus shipping
>>  - 10 qt aluminum pan and pickup for a Pantera - $375 plus shipping
>>  - Stock crankshaft x 3 - Come get'em or pay the shipping and they are
>> yours, otherwise they go to scrap
>>  - I might think of some other stuff later....
>> Kirby
>> _______________________________________________
>> 
>> Detomaso Forum Managed by POCA
>> 
>> DeTomaso mailing list
>> DeTomaso at poca.com
>> http://poca.com/mailman/listinfo/detomaso_poca.com
> 
> 
> _______________________________________________
> 
> Detomaso Forum Managed by POCA
> 
> DeTomaso mailing list
> DeTomaso at poca.com
> http://poca.com/mailman/listinfo/detomaso_poca.com