[DeTomaso] On the scrounge...
Kirby Schrader
kirby.schrader at gmail.com
Sun Mar 9 22:34:36 EDT 2014
http://www.bassettwheel.com
Weights are all listed with the sizes.
On Mar 9, 2014, at 20:37, LS <lashdeep at yahoo.com> wrote:
> Are the Bassets steel?
>
> If so, how much do they weigh?
>
> One of the reasons I have never considered bigger aftermarket wheels (besides looks, height, and lack of 17" tire choices) is the huge increase in weight.
>
> I remember the first time I picked up an aftermarket 17" rear wheel, I wanted it as far away from my car as possible due to the large weight difference over the factory 15s.
>
> I quickly realized that pushing the car away from the wheel was easier than vice versa!
>
> LS
>
>
>
> On Mar 9, 2014, at 18:16, Kirby Schrader <kirby.schrader at gmail.com> wrote:
>
>> Mike,
>>
>> Yes, indeed... Narrow body with fiberglass GTS flares.
>>
>> I checked their website and the backspacing/widths can be had for what
>> I want.
>>
>> I've queried them though to find out what the ID of the wheels is...
>>
>> Too many wheels are the right width and backspacing and won't fit over
>> the calipers.
>>
>> I'll see what they say.
>>
>> You are right though... some bargains!
>>
>> Thanks,
>>
>> Kirby
>>
>> On Mar 9, 2014, at 16:10, Mike Drew <[1]mikeldrew at aol.com> wrote:
>>
>> Kirby,
>> You can get those wheels in any width, any offset. Sorry I didn't twig
>> to the fact you have a narrow body car.
>> Mike
>> Sent from my iPhone
>> On Mar 9, 2014, at 13:49, Kirby Schrader <[2]kirby.schrader at gmail.com>
>> wrote:
>>
>> No.... Those won't work, Mike.
>> I do not have a Group 4.
>> I have GTS flares on the car.
>> I can go measure, but I think those wheels would have the tires
>> sticking out the side of the car.
>> The rears, for sure.
>> The fronts maybe....
>> On Mar 9, 2014, at 14:40, [3]MikeLDrew at aol.com wrote:
>>
>> In a message dated 3/9/14 6 49 55, [4]kirby.schrader at gmail.com
>> writes:
>>
>> I'm looking for a second set of wheels for the race car.
>>
>>>>> What you want are Bassett wheels. They make fantastic wheels
>> that are, when painted appropriately, a rough approximation of the
>> factory Gr4 wheels.
>> Wheel spec below.
>> 2 15"x13" D-Hole style with 5.5" back spacing....$109 each
>> 2 15"x10" D-Hole style with 4.5" back spacing....$92 each
>> All with a 4.5"bolt pattern.
>> Somewhere there's photos of a fantastic blue Gr4 clone wearing those
>> wheels, in gold. I couldn't find that on my hard drive (it's buried
>> somewhere) but I do have photos of a black street Gr4 clone with
>> those same wheels, also in gold (attached).
>> Frankly, these wheels are so good and so cheap that I would suggest
>> you buy two sets and scrap the ones you have now! :>)
>> Mike
>> <Bassett wheelsweb.jpg>
>>
>> References
>>
>> 1. mailto:mikeldrew at aol.com
>> 2. mailto:kirby.schrader at gmail.com
>> 3. mailto:MikeLDrew at aol.com
>> 4. mailto:kirby.schrader at gmail.com
>> _______________________________________________
>>
>> Detomaso Forum Managed by POCA
>>
>> DeTomaso mailing list
>> DeTomaso at poca.com
>> http://poca.com/mailman/listinfo/detomaso_poca.com
More information about the DeTomaso
mailing list