[DeTomaso] 351c Deck Height?
Ken Green
kenn_green at yahoo.com
Fri Dec 5 14:50:23 EST 2014
I have seen 351C head gasket descriptions with thickness between .027 and .120 (some even thicker):
http://www.jegs.com/p/Cometic-Gaskets/Cometic-Ford-351C-351M-400-Cylinder-Head-Gaskets/2849496/10002/-1
Seems like you could just get the right head gasket after the short block is done?
Ken
From: Corey Price <coreyjprice at gmail.com>
To: "detomaso at poca.com" <detomaso at poca.com>
Sent: Friday, December 5, 2014 11:34 AM
Subject: [DeTomaso] 351c Deck Height?
Yes, the standard answer for centerline of crank mains to head surface
is 9.206" for a 351 Cleveland.A What's funny is that my 30-yr-old
"Ford Performance" book states that the '71 Boss 351 block was between
9.201" and 9.211" and the rest of the 351 blocks are 9.213".A I'm sure
the 9.206" height I find in most literature is the average of 9.201"
and 9.211".A My machinist claims that most blocks are on the high side
of the specified deck height.A Not being a machinist, I can't tell one
way or another.A The reason I'm asking is that I'd like to order
pistons with the correct pin (compression) height and there's a readily
available piston in a 0.020" overbore from Probe that fits, but it
wouldn't give much room for surfacing the block deck if the deck height
is 9.201".A I'm not sure I have the tools to accurately measure deck
height.A The machinist said he usually checks for warping and height
with the pistons at four corners, but isn't that a little too late?
Corey
_______________________________________________
Detomaso Forum Managed by POCA
DeTomaso mailing list
DeTomaso at poca.com
http://poca.com/mailman/listinfo/detomaso_poca.com
-------------- next part --------------
I have seen 351C head gasket descriptions with thickness between .027
and .120 (some even thicker):
[1]http://www.jegs.com/p/Cometic-Gaskets/Cometic-Ford-351C-351M-400-Cyl
inder-Head-Gaskets/2849496/10002/-1
Seems like you could just get the right head gasket after the short
block is done?
Ken
__________________________________________________________________
From: Corey Price <coreyjprice at gmail.com>
To: "detomaso at poca.com" <detomaso at poca.com>
Sent: Friday, December 5, 2014 11:34 AM
Subject: [DeTomaso] 351c Deck Height?
Yes, the standard answer for centerline of crank mains to head
surface
is 9.206" for a 351 Cleveland.A What's funny is that my 30-yr-old
"Ford Performance" book states that the '71 Boss 351 block was
between
9.201" and 9.211" and the rest of the 351 blocks are 9.213".A I'm
sure
the 9.206" height I find in most literature is the average of 9.201"
and 9.211".A My machinist claims that most blocks are on the high
side
of the specified deck height.A Not being a machinist, I can't tell
one
way or another.A The reason I'm asking is that I'd like to order
pistons with the correct pin (compression) height and there's a
readily
available piston in a 0.020" overbore from Probe that fits, but it
wouldn't give much room for surfacing the block deck if the deck
height
is 9.201".A I'm not sure I have the tools to accurately measure deck
height.A The machinist said he usually checks for warping and height
with the pistons at four corners, but isn't that a little too late?
Corey
_______________________________________________
Detomaso Forum Managed by POCA
DeTomaso mailing list
[2]DeTomaso at poca.com
[3]http://poca.com/mailman/listinfo/detomaso_poca.com
References
1. http://www.jegs.com/p/Cometic-Gaskets/Cometic-Ford-351C-351M-400-Cylinder-Head-Gaskets/2849496/10002/-1
2. mailto:DeTomaso at poca.com
3. http://poca.com/mailman/listinfo/detomaso_poca.com
More information about the DeTomaso
mailing list