[DeTomaso] NPC! Need longer racing harness belt brackets for NORC/SSCC
Bjoern Flesland
bflesland at gmail.com
Fri May 6 17:11:33 EDT 2011
Hi AJ,
I am using an adjustable belt yes.
Adj. on the inside/camlock side.
What I need is a REGULAR bolt in/bolt down bracket, just a bit longer than the summit/jegs versions!
It will be fitted together with my stock lapbelt bracket on a 5/8 shoulder bolt.
Does that make sense?
Cheers Bjoern
Sent from my iPhone
Den 6. mai 2011 kl. 13:24 skrev asajay at asajay.com:
> You might try looking here:
> http://www.schrothracing.com/store/Competition/hardware/bolt-in-hardware
>
> Otherwise I'm not sure how to help. I'm having a hard time picturing
> the application.
>
> Are you using an adjustable belt? Adjustable at the inside (body)
> end, not the outside (attach point) end? I would think once you have
> it bolted down it shouldn't matter.
>
> Asa Jay
>
>
> Quoting Bjoern Flesland <bflesland at gmail.com>:
>
>> Hi AJ,
>> No this eyebolt and clip on bracket will not work unfortunately.
>> I need to use a bolt down bracket because of the very tight space.
>> There must be some race gear vendors that sells longer brackets I believe!?!?
>> Who can that be?
>> Cheers Bjoern
>>
>> Sent from my iPhone
>>
>>
>> Den 6. mai 2011 kl. 10:08 skrev Asa Jay Laughton <asajay at asajay.com>:
>>
>>> Bjoern,
>>>
>>> Another possible solution:
>>>
>>> Buy one or two of these:
>>> http://www.summitracing.com/parts/SIM-31018/
>>>
>>> Then a couple of these:
>>> http://www.summitracing.com/parts/GFR-107W/
>>>
>>> Be sure to use a small cotter pin or safety wire on the latch once
>>> they are attached. Part of the rules.
>>>
>>> This is what I used on my Pantera and they work great. This would
>>> give you the flexibility you need to thread the belt I think.
>>>
>>> The eye-bolt should fit any standard seat belt mounting hole.
>>>
>>> Let us know what you think.
>>> Asa Jay
>>>
>>> Quoting Bjoern Flesland <bflesland at gmail.com>:
>>>
>>>> Does anybody know where I quickly can I get hold of a longer type
>>>> of harness
>>>> belt "bolt down bracket ends"?
>>>> I only need one bracket.
>>>>
>>>> The ones they have at Summit and Jegs are just a bit too short.
>>>>
>>>> I need a bracket that sticks up more (is higher) when bolted in at the
>>>> factory lap belt mounting point.
>>>> This so I can access it and insert the lap belt thru it.
>>>>
>>>> Summit Racing call them "bolt down bracket", brand G-Force:
>>>>
>>>> G-FORCE Racing 103H* - G-FORCE Seat Belt Bolt-Down Ends*
>>>> G-FORCE Racing 103W* - G-FORCE Seat Belt Bolt-Down Ends*
>>>>
>>>> Both these 2 in and 3 in (belt width) types they have are a bit too short.
>>>>
>>>> Or does there maybe exist a type of extender that can be fitted?
>>>>
>>>> The bolt hole needs to be 5/8 in.
>>>>
>>>> Any help very much appreciated.
>>>> Cheers Bjoern
>>>> _______________________________________________
>>>>
>>>> Detomaso Forum Managed by POCA
>>>>
>>>> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>>>>
>>>> DeTomaso mailing list
>>>> DeTomaso at list.realbig.com
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
More information about the DeTomaso
mailing list