[DeTomaso] Caliper bolts--when was the last time you checked?
bill gaino
gaino at earthlink.net
Mon Sep 27 09:05:16 EDT 2010
I had a bolt fall out because I failed to bend the tab after service. It scared the crap out of me. I found a smaller bolt to hold things in place until I got to a shop with the right size. I made my own locking tabs, after mine were worn out. It is important to keep these bolts in! Bill{ craped his pants} 1362
-----Original Message-----
>From: Asa Jay Laughton <asajay at asajay.com>
>Sent: Sep 27, 2010 8:56 AM
>To: doug351c at gmail.com, Ken Green <kenn_green at yahoo.com>, dickruzzindesign <dickruzzindesign at aol.com>
>Cc: DeTomaso Forum <detomaso at realbig.com>
>Subject: Re: [DeTomaso] Caliper bolts--when was the last time you checked?
>
>Last time I checked, they were Damn expensive and I wasn't into paying Ferarri prices. Has that changed?
>
>Asa Jay
>Sent using Elfen Magic.
>
>-----Original Message-----
>From: "doug351c" <doug351c at gmail.com>
>Sender: detomaso-bounces at realbig.com
>Date: Sun, 26 Sep 2010 22:56:35
>To: Ken Green<kenn_green at yahoo.com>; dickruzzindesign<dickruzzindesign at aol.com>
>Reply-To: doug351c at gmail.com
>Cc: DeTomaso Forum<detomaso at realbig.com>
>Subject: Re: [DeTomaso] Caliper bolts--when was the last time you checked?
>
>Yes, it assumes you have the metal tabs. But they are quite inexpensive
>from the vendors if you don't have them any longer.
>
>Doug
> -----Original Message-----
> From: Ken Green [mailto:kenn_green at yahoo.com]
> Sent: Sunday, September 26, 2010 8:52 PM
> To: dickruzzindesign; doug351c at gmail.com
> Cc: DeTomaso Forum
> Subject: Re: [DeTomaso] Caliper bolts--when was the last time you checked?
>
>
> I wonder if that assumes you have the metal tabs also? With
>the potential heat cycling, it seems like some form of hi temp locktite (if
>there is such a thing) or safety wire would be a good thing.
>
> Ken
>
> --- On Sun, 9/26/10, doug351c <doug351c at gmail.com> wrote:
>
>
> From: doug351c <doug351c at gmail.com>
> Subject: Re: [DeTomaso] Caliper bolts--when was the last
>time you checked?
> To: "dickruzzindesign" <dickruzzindesign at aol.com>,
>MikeLDrew at aol.com, detomaso at realbig.com
> Cc: "DeTomaso Forum" <detomaso at realbig.com>
> Date: Sunday, September 26, 2010, 5:52 PM
>
>
> Dick,
> Front Brake Caliper to Spindle Bolt : 50-55 ft-lbs
>
> Rear Brake Caliper to Upright Bolt : 35-40 ft-lbs
>
> Doug Braun
> blue 73L #5505
>
> -----Original Message-----
> From: dickruzzindesign [mailto:dickruzzindesign at aol.com]
> Sent: Sunday, September 26, 2010 2:14 PM
> To: doug351c at gmail.com; MikeLDrew at aol.com;
>detomaso at realbig.com
> Subject: Re: [DeTomaso] Caliper bolts--when was the last
>time you checked?
>
>
> Mike,
> What is the recommended torque value for the caliper
>bolts?
> --
>
> All the best,
> DICK RUZZIN
>
>_____________________________________________________________________
> dickruzzinDESIGN at aol.com / Home: 313-824-0539 / Cell:
>313-300-9558
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at
>http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
>
>
>_______________________________________________
>
>Detomaso Forum Managed by POCA
>
>Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
>DeTomaso mailing list
>DeTomaso at list.realbig.com
>http://list.realbig.com/mailman/listinfo/detomaso
>_______________________________________________
>
>Detomaso Forum Managed by POCA
>
>Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
>DeTomaso mailing list
>DeTomaso at list.realbig.com
>http://list.realbig.com/mailman/listinfo/detomaso
If you want it SLICK.. bring it to SLICKUM Paint Shop www.slickpaint.com
More information about the DeTomaso
mailing list