[DeTomaso] machine ball joint to modify alingment

Will Kooiman wkooiman at earthlink.net
Fri May 21 00:08:56 EDT 2010


Aren't you just speculating that we can solve this with a photo with the
wheel off the car?

If the wheel is off the car, how are you going to spin it?  Answer me that,
batman.

Einstein would say, that no, the a-arms have not moved forward, but
everything else has moved backward.

Sorry - couldn't help myself.  Actually, I guess I could have, but I didn't.

-----Original Message-----
From: detomaso-bounces at realbig.com [mailto:detomaso-bounces at realbig.com] On
Behalf Of Asa Jay Laughton
Sent: Thursday, May 20, 2010 11:03 PM
To: detomaso at realbig.com
Subject: Re: [DeTomaso] machine ball joint to modify alingment

We need a photo with the wheel off the car.  We need to have a good look 
at the a-arm bushings and the upper ball joint adjustment.  It appears 
the a-arms are moved forward as is possibly the ball joint, from putting 
all the shims to the rear.  We can speculate all we want, but until we 
have closer photos of the suspension components without the wheel on... 
well we're all just spinning our wheels.

Asa Jay

Asa Jay Laughton, MSgt, USAFR, Retired
&  Shelley Marie
Spokane, WA
******************************
http://www.racingagainstautism.com
http://www.teampanteraracing.com


On 5/20/2010 20:54, Will Kooiman wrote:
> One thing to consider is the front right might have been rearranged from
an
> accident.
>
> I haven't read this entire thread, though.  If the misalignment occurred
> after changing the a-arm, it's probably the a-arm.  From the photo, it
looks
> like caster was added in the wrong direction (removed caster).
>
> I'm definitely no expert on alignment, but I always thought that when you
> added caster, the wheel moves back in the wheel well - slightly.  Right?
>
> And, even if the shim were added on the wrong side, it should just put
> caster back in the stock range.
>
> -----Original Message-----
> From: detomaso-bounces at realbig.com [mailto:detomaso-bounces at realbig.com]
On
> Behalf Of Julian Kift
> Sent: Thursday, May 20, 2010 10:43 PM
> To: boyd411 at gmail.com; steveblum2 at msn.com
> Cc: guson at home.se; De Tomaso List
> Subject: Re: [DeTomaso] machine ball joint to modify alingment
>
>
> Rather than use all those individual shims I did same as Johnny and
> fabricated a spacer out of a 3/4" square piece of aluminum stock and just
> used the original thin shims for fine adjustment. As the 'shim' is now one
> piece of stock it is more obvious that it goes in front of the ball joint.
>
>
>
> Julian
>
>
>
> Date: Thu, 20 May 2010 23:13:46 -0400
> Subject: Re: [DeTomaso] machine ball joint to modify alingment
> From: boyd411 at gmail.com
> To: steveblum2 at msn.com
> CC: julian_kift at hotmail.com; guson at home.se; detomaso at realbig.com
>
> The word is that he is a first rate ass hole.
> This is what Johnny Sent me.
>
>
>
> Alignment specs:
>
>
>
>
> My car is narrow bodied GTS with 16x8 245/45 front and 17x11 335/35 on the
> rear.
> If you have smaller wheels&  tyres these specs still apply.
> On the front I like to run between 6 and 7 degrees of caster (the ally
> spacer I have made for you will get you in that ball park) It's actually
> more important to get the caster the same side to side than getting it
> exactly 5, 6 or 7 degrees. Originally your car could get a maximum or
2,1/2
> degrees caster. You can now get up to 7 degrees. 7 will give you the most
> self centring and high speed stability but 6 or 5 degrees will make your
> steering slightly lighter. You may have to make the ally spacer a bit
> narrower to get 5 degrees. I run 6 degrees and like it.
> I set the toe in a 1/16th and the camber at 1/2 a degree negative (in at
the
> top) It's very important to take the car for a drive after each camber
> change to let the suspension settle and re-check it. The camber lock I
have
> added to your A arm will make this job a lot easier.
> If you dont get the camber exactly the same either side the car will pull
to
> the left or right under braking.
>
> On the rear set the toe in at 0 and the camber at 1/4 -1/2 negative (in at
> the top) I have mine set at 1/2 and get good tyre life.
>
> Regards, Johnny
>
>
> On Thu, May 20, 2010 at 11:10 PM, STEVEN BLUM<steveblum2 at msn.com>  wrote:
>
>
> I have attempted to contact Pat in the past about the modification to
> request instructions. He has ignored my calls.
>
>
> Steven Blum
> P.O. Box 81
> Shoreham, N.Y. 11786
> H (631) 744-6118
> C (631) 235-1905
>
>
>
>
>
>
> From: julian_kift at hotmail.com
> To: steveblum2 at msn.com; guson at home.se; detomaso at realbig.com
>
> Subject: RE: [DeTomaso] machine ball joint to modify alingment
> Date: Thu, 20 May 2010 20:04:42 -0700
>
>
>
>
>
>
> Steve,
>
> I only saw the photo Mike Drew posted of the passenger side with the wheel
> on, does the driver side look different, further to the rear? You'll have
to
> recheck you toe as well as the a-arms change and movement rearward may
have
> affected that too.
>
> We had a discussion about the a-arm mods recently and Pat was quite vocal,
I
> would suggest forwarding the photo's to him for comment in support of his
> product and whether it has been fitted correctly.  My modified a-arms are
> set up with the ball joint all the way back, no shims at the rear. No
> instructions as I modified them myself...
>
> Goos luck,
> Julian
>
>    
>> From: steveblum2 at msn.com
>> To: guson at home.se; detomaso at realbig.com
>> Date: Thu, 20 May 2010 20:29:26 -0400
>> Subject: Re: [DeTomaso] machine ball joint to modify alingment
>>
>>
>> The A arm modification was done by Pat Michals and supposedly installed
>>      
> per his instructions. Somehow I think either the shop did not understand
his
> instructions or he gave them the wrong instructions. I think it waqs the
> shop but cannot be sure as hey never gave me his instructions when I
picked
> up the car. They said they were misplaced. Are you sure that the shims on
> both sides are wrong? I can uderstand the right side but if I move the
> drivers side to the front won't the whell be to far back?
>    
>> Steven Blum
>> P.O. Box 81
>> Shoreham, N.Y. 11786
>> H (631) 744-6118
>> C (631) 235-1905
>>
>>
>>
>>
>>      
>>> From: guson at home.se
>>> To: detomaso at realbig.com
>>> Date: Thu, 20 May 2010 23:59:55 +0200
>>> Subject: Re: [DeTomaso] machine ball joint to modify alingment
>>>
>>> A close-up pic of the A-arms in the wheel well would be nice to see.
>>>        
> With
>    
>>> the wheel removed that is.
>>>
>>> Tomas
>>>
>>> -----Original Message-----
>>> From: detomaso-bounces at realbig.com
>>> [mailto:detomaso-bounces at realbig.com]On Behalf Of Julian Kift
>>> Sent: den 20 maj 2010 22:59
>>> To: steveblum2 at msn.com; mikeldrew at aol.com; De Tomaso List
>>> Subject: Re: [DeTomaso] machine ball joint to modify alingment
>>>
>>>
>>> I see you have the modified upper a-arms to improve your caster. To take
>>> advantge of that the ball joint (and wheel) should be moved rearwards by
>>> ideally locating all the shims in front of the ball joint. Once done,
>>>        
> get
>    
>>> the shop to fine tune using a caster gauge to get the two sides equal by
>>> varying shims.
>>>
>>>
>>>
>>> What I don't understand at present is the way you currently have the
>>>        
> shims
>    
>>> would be about right for stock caster, but a stock car would not have
>>>        
> the
>    
>>> wheel that far forward in the fender. Do you know who undertook the
>>> modification to the a-arms?
>>>
>>>
>>>
>>> Julian
>>>
>>>
>>> From: steveblum2 at msn.com
>>> To: julian_kift at hotmail.com; mikeldrew at aol.com; detomaso at realbig.com
>>> Subject: RE: [DeTomaso] machine ball joint to modify alingment
>>> Date: Thu, 20 May 2010 16:16:30 -0400
>>>
>>>
>>>
>>> Attached are photos of both sides. The shims on both sides are to the
>>>        
> rear
>    
>>> so that looks good. When I get it on the alignment rack i need to
>>>        
> compare
>    
>>> wheelbase measurements, it looks like I need to move some right side
>>>        
> shims.
>    
>>> Steven Blum
>>> P.O. Box 81
>>> Shoreham, N.Y. 11786
>>> H (631) 744-6118
>>> C (631) 235-1905
>>>
>>>
>>>
>>>
>>>
>>>
>>> From: julian_kift at hotmail.com
>>> To: mikeldrew at aol.com; steveblum2 at msn.com; detomaso at realbig.com
>>> Subject: RE: [DeTomaso] machine ball joint to modify alingment
>>> Date: Thu, 20 May 2010 09:15:55 -0700
>>>
>>>
>>>
>>> That is a lot of forward shift, more than one would imagine possible
>>>        
> through
>    
>>> the bushing orientation or having the ball joint shims on the wrong
>>>        
> side, or
>    
>>> both. This might be a dumb question, but were both sides apart at the
>>>        
> same
>    
>>> time, is there any chance that they got the a-arm sides or orientation
>>>        
> mixed
>    
>>> up? e.g. an upside down upper a-arm would have significant forward shift
>>>        
> of
>    
>>> the upper ball joint.
>>>
>>> Can you take a photo of the suspension arms with the wheel removed?
>>>
>>> Julian
>>>
>>>        
>>>> From: MikeLDrew at aol.com
>>>> Date: Thu, 20 May 2010 11:34:58 -0400
>>>> To: steveblum2 at msn.com; detomaso at realbig.com
>>>> Subject: Re: [DeTomaso] machine ball joint to modify alingment
>>>>
>>>>
>>>> In a message dated 5/20/10 8 22 49, steveblum2 at msn.com writes:
>>>>
>>>>
>>>>          
>>>>> I recently found what I suspect is a problem with the front end.
>>>>> Aparently when I had the suspension bushings changed the new ones
>>>>>            
> were
>    
>>> installed
>>>        
>>>>> wrong causing an alignment problem. My question is, how much of a
>>>>>            
>>> project is
>>>        
>>>>> it to disassemble the front end, correct the busing and reassemble
>>>>>            
> the
>    
>>>>> front end? Is this a job only for an experienced mechanic or someone
>>>>>            
>>> with
>>>        
>>>>> mechanical skills but limited experience can handle? What special
>>>>>            
> tools
>    
>>> are
>>>        
>>>>> required?
>>>>>
>>>>>            
>>>> Another point--when your front end was reassembled, all the shims etc.
>>>> should have gone towards the front side of the upper ball joint,
>>>>          
> pushing
>    
>>> it
>>>        
>>>> relatively rearwards. It's possible that they were put towards the
>>>>          
> back
>    
>>> side,
>>>        
>>>> which would totally jack up your alignment and contribute to the
>>>>          
> problem
>    
>>>> you're having.
>>>>
>>>> You should post the photo you sent me so people can see what we're
>>>>          
> talking
>    
>>>> about. Or better yet, I will:
>>>>
>>>> http://tinyurl.com/22olpcz
>>>>
>>>> Mike
>>>> _______________________________________________
>>>>
>>>> Detomaso Forum Managed by POCA
>>>>
>>>> Archive Search Engine Now Available at
>>>>          
> http://www.realbig.com/detomaso/
>    
>>>> DeTomaso mailing list
>>>> DeTomaso at list.realbig.com
>>>> http://list.realbig.com/mailman/listinfo/detomaso
>>>>          
>>>
>>>
>>> The New Busy think 9 to 5 is a cute idea. Combine multiple calendars
>>>        
> with
>    
>>> Hotmail. Get busy.
>>> _________________________________________________________________
>>> The New Busy think 9 to 5 is a cute idea. Combine multiple calendars
>>>        
> with
>    
>>> Hotmail.
>>>
>>>        
>
http://www.windowslive.com/campaign/thenewbusy?tile=multicalendar&ocid=PID28
>    
>>> 326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_5
>>> _______________________________________________
>>>
>>> Detomaso Forum Managed by POCA
>>>
>>> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>>>
>>> DeTomaso mailing list
>>> DeTomaso at list.realbig.com
>>> http://list.realbig.com/mailman/listinfo/detomaso
>>>
>>> _______________________________________________
>>>
>>> Detomaso Forum Managed by POCA
>>>
>>> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>>>
>>> DeTomaso mailing list
>>> DeTomaso at list.realbig.com
>>> http://list.realbig.com/mailman/listinfo/detomaso
>>>        
>> _______________________________________________
>>
>> Detomaso Forum Managed by POCA
>>
>> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>>
>> DeTomaso mailing list
>> DeTomaso at list.realbig.com
>> http://list.realbig.com/mailman/listinfo/detomaso
>>      
>
>
>
> Hotmail has tools for the New Busy. Search, chat and e-mail from your
inbox.
> Learn more.
>
>
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
>
>   		 	   		
> _________________________________________________________________
> The New Busy is not the too busy. Combine all your e-mail accounts with
> Hotmail.
>
http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID283
> 26::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com
> http://list.realbig.com/mailman/listinfo/detomaso
>
>    
_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at list.realbig.com
http://list.realbig.com/mailman/listinfo/detomaso




More information about the DeTomaso mailing list