[DeTomaso] Steering Shaft Slip Joint

[Steve Hawkins]

Similar to what I did but I used aluminum.

Steve

-----Original Message-----
From: detomaso-bounces at realbig.com [mailto:detomaso-bounces at realbig.com] On
Behalf Of Art Stephens
Sent: Wednesday, March 31, 2010 5:37 PM
To: tmshinro at aol.com; detomaso at realbig.com
Subject: Re: [DeTomaso] Steering Shaft Slip Joint


Good idea Tom!  Along the same lines,  I used a feeler gauge to find the 
tightest fit I could get.  I then just cut off part of that gauge,  shoved 
it in place and used electrical tape to make sure it didn't work itself out.

Art



----- Original Message ----- 
From: <tmshinro at aol.com>
To: <detomaso at realbig.com>
Sent: Wednesday, March 31, 2010 1:59 PM
Subject: [DeTomaso] Steering Shaft Slip Joint


>
> I had some slop in my slip joint and I inserted a brass shim in the 
> joint
> to fill the void.  Went to a hobby store to get some brass sheet stock of 
> the needed thickness and cut out a piece to fit into the joint.  Was an 
> easy fix and it hasn't loosened up yet (23 years and counting)
>
> Tom
> #5186
>
>
>
>
>
>
>
>
> -----Original Message-----
> From: MikeLDrew at aol.com
> To: hemipanter at hemipanter.se
> Cc: detomaso at realbig.com
> Sent: Wed, Mar 31, 2010 3:38 pm
> Subject: Re: [DeTomaso] need data on other cars re Hemmings article
>
>
>
> In a message dated 3/31/10 13 24 25, hemipanter at hemipanter.se writes:
>
>
>> Looks like a skrew blocking the deformation section of the steering 
>> axle?
>>
> http://www.poca.com/index.php/gallery/?g2_itemId=9220
>
>
>>>>Yes--I had a ton of slop there, and Dennis Quella and other 
>>>>recommended
> using a bolt and nut arrangement to pinch the outer portion against the
> inner portion.   Unfortunately it's not as effective as I would have 
> hoped, plus
>
> I've lost the ability of that piece to collapse in a front-end 
> collision. I'm not overly concerned about that, since I wear 
> five-point harnesses even when I drive around the block.
>
> However, I still have unwanted play in the slip joint; while the bolt 
> did pull the center of the outer portion in, the corners are really 
> where it acts againt the inner piece, and they are still too far out.
>
> There are various methods of dealing with that--Wilkinson to me to 
> place the assembly in a 60-ton press and smash the flat sides flat (a 
> 20-ton press doesn't have enough oomph to do that job, as the pieces 
> in question are
> extremely hard).   Another solution (I believe from Quella) would be to
> tack-weld
> the corners--making the unit rigid, but the welds weak enough to break 
> in the event of a collision and still allow the unit to collapse.
>
> I intend to deal with it in the next few months--one way or the other,
> that
> bolt will be gone before long.
>
> Mike
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at 
> http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com 
> http://list.realbig.com/mailman/listinfo/detomaso
>
>
> _______________________________________________
>
> Detomaso Forum Managed by POCA
>
> Archive Search Engine Now Available at 
> http://www.realbig.com/detomaso/
>
> DeTomaso mailing list
> DeTomaso at list.realbig.com 
> http://list.realbig.com/mailman/listinfo/detomaso


----------------------------------------------------------------------------
----



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.791 / Virus Database: 271.1.1/2781 - Release Date: 03/30/10 
23:32:00

_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at list.realbig.com http://list.realbig.com/mailman/listinfo/detomaso