[DeTomaso] EFI fuel line attachment through the gas tank drain plug suggestions?

[Ken Green]

I tracked down the M22 banjo fitting for a 1/2 inch rubber hose and M22 bolt, both for about $13 plus shipping.  I'll probably order them.  Does anyone else want them?
 
Ken

--- On Mon, 3/29/10, Julian Kift <julian_kift at hotmail.com> wrote:


From: Julian Kift <julian_kift at hotmail.com>
Subject: Re: [DeTomaso] EFI fuel line attachment through the gas tank drain plug suggestions?
To: doug at silicondesigns.com
Cc: kenn_green at yahoo.com, "De Tomaso List" <detomaso at realbig.com>
Date: Monday, March 29, 2010, 10:03 PM



A call to your local Parker store should get a hit, not all Parker fittings are listed online. This is actually a 90 degree elbow M22 to -10AN line as described on page K46 of this catalog for European fittings... I know of people that have purchased this from their local US Parker store.



http://www.parker.com/docs/Literature/Tube%20Fittings%20Division%20Europe/test/UK/Chapter%20K%20UK.pdf

Here's some alternatives;

http://97.74.103.94/files/metric.pdf BatInc. offers -AN 8, 10, 12 & 16 to M22 adapters, metric banjo fittings etc.

http://www.touratech-usa.com/shop/show.lasso?sku=015-0055 Temp sensor adapter M22 male to M10 female



http://www.generalpump.com/PDFs/QDs-Plugs-Ftgs.pdf M22 male to NPT female fitting (common on pressure washers and available from many online washer parts stores)

Sorry I didn't explain the pdf link too well, it was more for the banjo fitting in M22, than the bushing. The banjo allows you to be right up under the tank and offers a little more under car road clearance than a 90 degree fitting can offer.


Good luck,

Julian




> From: doug at silicondesigns.com
> To: julian_kift at hotmail.com
> CC: detomaso at realbig.com; kenn_green at yahoo.com
> Subject: RE: [DeTomaso] EFI fuel line attachment through the gas tank drain plug suggestions?
> Date: Mon, 29 Mar 2010 15:04:23 -0800
> 
> Julian,
> 
> I tried searching Parker's website but I get no hits for # 10M22C80MXS; do
> you happen to have a webpage link to this fitting?
> 
> Also, the pdf page shows male-NPT/female-metric pipe bushings but we need
> male-metric/female-NPT; any suggestions?
> 
> Doug Braun
> blue 73L #5505
> 
> -----Original Message-----
> From: detomaso-bounces at realbig.com
> [mailto:detomaso-bounces at realbig.com]On Behalf Of Julian Kift
> Sent: Sunday, March 28, 2010 7:29 AM
> To: thomas.tornblom at hax.se; kenn_green at yahoo.com
> Cc: De Tomaso List
> Subject: Re: [DeTomaso] EFI fuel line attachment through the gas tank
> drain plug suggestions?
> 
> 
> 
> Yes earlier tanks are M22x1.5 drain plug and others that have drawn fuel
> from the bottom of the tank have used a M22 to AN fiitting. I did similar on
> my radiator for an aftermarket temp sensor and found a M22 to npt reducer.
> Parker Hydraulics fitting # 10M22C80MXS or
> http://www.summersrubber.com/pdf/224.pdf for metric to npt bushings.
> 
> 
> 
> Julian
> 
> 
> 

                          
_________________________________________________________________
The New Busy is not the old busy. Search, chat and e-mail from your inbox.
http://www.windowslive.com/campaign/thenewbusy?ocid=PID27925::T:WLMTAGL:ON:WL:en-US:WM_HMP:032010_3
_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at list.realbig.com
http://list.realbig.com/mailman/listinfo/detomaso