[DeTomaso] [NPC] Selecting air drills

[Mark McWhinney]

I hate to mention it, but this looks pretty good for the price.  If it can
last for the three small holes that I need to drill, it should be worth it
even if it goes up in smoke after that.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=45338



-----Original Message-----
From: detomaso-bounces at realbig.com [mailto:detomaso-bounces at realbig.com] On
Behalf Of Dave Doddek
Sent: Tuesday, January 15, 2008 8:01 PM
To: detomaso at realbig.com
Subject: Re: [DeTomaso] [NPC] Selecting air drills

If you dont plan on using the drill daily, do what I did and go to walmart
and buy a Black and Decker for $50.

Dave "B&D is reasonable quality" D

At 09:38 PM 1/14/2008 -0800, you wrote:
>Mark:
>
>You need a Milwaukee half inch VSR hammer drill. This will run in the
neighborhood of $200 or so. This will also be the finest corded portable
power tool you'll ever have. The Milwaukee brand is outstanding. Also if
you're anywhere in the SF/Sacramento area, I'd be glad to loan you mine. 
>
>If  you are the true "toolaholic", then you won't be happy until you have
your very own hammer drill. www.toolking.com in Colorado is an excellent
vendor, and here is their link for this drill:
>http://www.toolking.com/milwaukee_5378-21.aspx   This tool is $140, MSRP
of $201. 
>
>One thing, there's single range, and dual range hammer drills. If you
have, or anticipate, a "serious" amount of concrete drilling, then go for
the dual range. It's a must. Also get the keyed chucks. It's not nearly as
convenient as a keyless chuck, but the intense vibration that a hammer
drill generates will unlock a keyless chuck in seconds... especially when
you hit a "hard spot" in the concrete. And nothing slows the job down like
a drill bit that isn't spinning.... not that I'd know about that.... 
>
>Chris
>
>Chris Difani
>'73 L #5829 "LITNNG"
>The Electric Pantera
>Sacramento, CA
>Email: cdifani at pacbell.net 
>
>
>---------------------------------------------------------------------------
-----
>
>----- Original Message ----- 
>From: "Mark McWhinney" <msm at portata.com>
>To: <detomaso at realbig.com>
>Sent: Monday, January 14, 2008 3:48 PM
>Subject: [DeTomaso] [NPC] Selecting air drills
>
>
>>I am trying to drill some holes into concrete slab (garage floor) for some
>> anchor bolts.  My battery powered drill which has served me well for
years
>> is not up to the job.  It gets part way then jams up.
>> 
>> This is a good excuse to go get an air drill.  The question is what to
get.
>> The 1/2", pistol grip drills are all rated about 4 or 5 CFM air
consumption
>> but have free speeds of 500 to 2,500 RPM.  I assume that they are the
same
>> under the covers but have different gearing for the different top-end
>> speeds.  Since I need more torque than speed, should I go for the
low-speed
>> drills?  (Most manufactures specify their free speeds but not their
torque,
>> hence the question.)
>> 
>> 
>> 
>> 
>> _______________________________________________
>> 
>> Detomaso Forum Managed by POCA
>> 
>> Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>> 
>> DeTomaso mailing list
>> DeTomaso at list.realbig.com
>> http://list.realbig.com/mailman/listinfo/detomaso
>_______________________________________________
>
>Detomaso Forum Managed by POCA
>
>Archive Search Engine Now Available at http://www.realbig.com/detomaso/
>
>DeTomaso mailing list
>DeTomaso at list.realbig.com
>http://list.realbig.com/mailman/listinfo/detomaso
>
>
>

_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at list.realbig.com
http://list.realbig.com/mailman/listinfo/detomaso