Chuck, This is exactly what Hall Pantera sold as their Super Stopper II brake system. They used redrilled Corvette rotors and Corvette calipers with adapter brackets. You might even be able to buy those rotors already modified, directly from Hall? You would have to be awfully bored to contemplate doing this on your own when there are so many superior options available for a fraction of the effort and cost. Also, when was the last time you drove your car so hard that the stock rear rotors were insufficient? I have found that even at WFO speeds, on the street, vented Mustang front rotors and stock rear rotors work just fine. The track is a different story…. Mike Sent from my iPad
On Apr 18, 2025, at 20:00, LINDA HUBER <lindahuber@cox.net> wrote:
Has anyone done this, and possibly confirm a 1985 GM Corvette front rotor can be used as a Pantera replacement? I have access to a machine shop…
PANTERA — AMERICAN BRAKES, THE REAR END:
(NOTE: This article came from a Ted Mitchell article in the POCA: Pantera Technical Information binder, revised 7/13/88…. There were references to JFZ calipers. I am mostly interested in the vented rotor portion of the article…)
….Adapters and calipers work on the Pantera original equipment rear rotors and with a much better rotor - one with a Corvette part number.
Because the G.M. Pantera rear rotors are so similar the G.M. rotor can be used to replace the Pantera rear rotor at any time, and the same calipers and adapters are all easily refitted. It's a better-than-stock balanced system - simply by adapting new calipers to the front side of the rear rotors and moving the rear hydraulic flex lines from the old calipers to the new. The flex lines removed from the original wheel cylinders easily reach the new calipers.
This G.M. part is a late model Corvette FRONT rotor. It is 11 and 1/2 inches in diameter by 13/16 thick, and has a cast-in hat - all very much like a Pantera
REAR rotor.
If you lay this Chevy (front) rotor beside the Pantera (rear) rotor you'll notice two things. The superior quality of G.M. rotor makes the Pantera part look like junk, but in overall size and shape, the two parts are almost identical.
FITTING AND REFITTING THESE PARTS. Like the original equipment rotor, the G.M. part mounts under the rear axle hub -not the best way to mount a brake rotor -it makes changing the rotor difficult -and it unnecessarily transfers unwanted heat from the brakes to the wheel bearings. Race car makers just slip the rear rotors over the outside of the wheel lugs, so that the rotors are as easily changed as tires.
Measurements of the G.M. and Pantera rotors will show some differences that must be considered. The Vette rotor-hat has a little over 1/8th inch MORE offset than the stock Pantera item. AND, the Pantera rotor actually has 1/16” larger circumference than the G.M. part. A 1/16th of an inch closer rotor edge-to-caliper clearance will usually require no change. If the edge of the rotor rubs the caliper any brake shop can quickly restore clearance by turning a few thousandths of an inch off of the edge of the rotor. The 1/8th inch offset difference is even more easily handled, and we'll deal with that in a minute.
First the center of the Chevy part must be redrilled to a Ford /Pantera bolt pattern, and the center hole needs to be enlarged slightly to register properly on the Pantera stub-axle. These are simple jobs for even the most rudimentary machine shop. And, considering that the result is a vented rotor that is superior to the stock item in every respect, it is well worth this small trouble.
After the rotor is assembled to the axle and inserted into the upright, check for interference between the rotor inner rim and the caliper boss on the upright. Casting differences may cause conflict between the Pantera & Chevy parts where the inside rim of the Chevy rotor passes closest to the Pantera caliper mounting boss. If this happens a little filing on the corner of the caliper boss will quickly restore necessary clearance. These reworked Corvette rotors have a number of advantages over both stock parts and other more extensive brake modifications. (1) With these rotors the original Pantera parking brakes may be used. Stock calipers mag be remounted in their usual place. Just insert 1/8th inch thick spacer-washers between the caliper and the mounting face on the Pantera upright. This spacer compensates for the extra offset of the Chevy part thereby reestablishing the proper caliper location.
Then, hook up the parking brake cables but not the hydraulic lines. (2) Adapters which fit JFZ calipers to the Pantera rotors will also mate them properly to the newly mounted Corvette rotors. Insert spacer washers under each adapter and mount the caliper on the front or unused boss on each rear up-right, and hook up the Pantera hydraulic line.
I repeat - the flex lines from the rear-of-the-rotor calipers reach the front-of-the-rotor ones perfectly. (3) One final benefit! These rotors are available at your local Chevy dealer, and they currently retail for around $65 each - and who pays retail? _______________________________________________
Detomaso Email List is not managed by POCA Posted emails must not exceed 1.5 Megabytes DeTomaso mailing list -- detomaso@server.detomasolist.com To unsubscribe send an email to detomaso-leave@server.detomasolist.com
To manage your subscription (change email address, unsubscribe, etc.) use the links above.
Members who post to this list grant license to the list to forward any message posted here to all past, current, or future members of the list. They also grant the list owner permission to maintain an archive or approve the archiving of list messages.